I would LOVE for this to be available. ... View more

We also have this problem. A hat is indeed needed. RainX is an interesting solution though, haven't tried that. I also wish we could control the IR because sometimes it reflects inside the dome and just makes a mess. In some situations we have turned the IR off because the ambient light is "good enough" compared to the washed out IR. A few situations we have actually got a PoE powered IR flood and used that instead of the camera IR, this also works pretty well.   We also have our maintenance teams clean the cameras very often which helps as well but is annoying for 100s of cameras. We've done quite a few case studies and betas and on every one we have recommended a hat... ... View more

@Eskimo007 it isn't great at all, I'd go with 2. WPA2 for the moment. ... View more

Thanks for your quick response! ... View more

Guys.. it was so simple. A firmware upgrade was needed... it hadn’t been done for about a year. With the new firmware it works again. Thanks for the support! ... View more

I honestly kind of wish the industry as a whole would get rid of L2TP client VPN. It seems to be this half-supported technology that some companies have phased out and others have left but don't really pay too much attention to. ^ Not just speaking of Meraki on this on - I'm finding other vendors have unofficially given up on it. ... View more

We still had our suspicion on 24H2. It happened to different networks across different organizations.  Its hard to report the issue to Microsofy as these things happened randomly ... View more

Hey @AmeyGadre  - drop me a DM with a link to your MV and I can confirm for you, otherwise yes, whomever manages the switch will be able to confirm.   To raise a Support Case, see this KB: https://documentation.meraki.com/General_Administration/Support/Ways_to_Contact_Meraki_Support ... View more

This was just one side of the coin. Customer do have several offices that do not have any IT-personel on site. They want to install the most newest HW to these sites to avoid any additional travelling on site. Thats the original reason so just optimizing operations. ... View more

We'll happily join, or host a meeting if required. What sometimes may happen though is that Support will ask for justification / context about said meeting - we operate primarily as an inbound call centre, so Support may push back on joining a bridge/meeting if there's no context or ask, this is so we can prioritise NSE time to helping solve issues, rather than potentially sitting on an idle bridge when we could be helping others. ... View more

 ipad has been enrolled, ade status pushed, however still it shows the attached error. Moreover it is not getting supervise also. What could be the problem  ... View more

When you are pinging the AP's from your infrastructure you are not testing client experience but rather the management plane connection speed between the AP and your monitoring system.  As @cmr has mentioned, the AP could be busy and be a little slow to respond to ICMP echoes.   Things you should be monitoring are the following: Channel airtime AP CPU and RAM Client RSSI/SNR Average client onboarding experience Average client frame latency and drops. Channel airtime can be viewed from dashboard and is maybe available via the API, not sure. Onboarding expierence can be vewed per AP or per client. RSSI/SNR can be viewed in client view or by going to the AP and viewing the currently connected clients. Average frame latency and drops can be viewed from the RF spectrum page. You can also have thousandeyes integration with your managed clients to see their wireless experience over time. ... View more

I think credentials are not stored as clear text. So it is not possible to show the configured password. The show button shows the password only while configuring it. ... View more

If you hover over the red in the "Historical device data" - what reason does it give?       ... View more

@ConnorL  is perfectly on point here. You should be seeing reCaptcha widget when you are on this page. See my step-by-step screenshots below, for reference:   This is often due to browser issues, temporary network problems, or extensions interfering with the process. Try another browser (possibly incognito mode) - to verify if this behavior is across different browsers. If you see this across different browsers, try using another ISP connection (or phone hotspot) for comparison. ... View more

This is what is causing the issue. Any idea when the new UI is going to come out of Beta or we can at least disable it?  ... View more

You're licensed for 1 AP (and 1 MX and 2 switches) and you have 2 APs. So it's out of compliance. You need an additional AP license. ... View more

Hi, Many thanks for the replies. I have got a grace period on the dashboard, so network work back normal. I added one license as renewal when it should have been add device. This cancels out the previous one. It is not easy to understand the dashboard for license as well as understanding the adding of new ones. This element of license is key to the platfrom, which just needs to be made easier. ... View more

The status page shows it started about an hour later that reported by @DevOps_RC , but shows resolved at 16:24 UTC, looks like they were down for the working day, but recovered now. ... View more

The organization is new and already licensed, the devices are not claimed by another organization, which makes it even stranger. ... View more

100%, you can't bypass 802.1X that happens before an IP is issued. Any bypass like MAB would have to be on the actual RADIUS server... ... View more

Hmm, the only thing I can think of initially is that the App Bundle ID matches one that's in Google Play, hence why you're being redirected there to download it officially. Mind dropping me a DM? In the meantime, I recommend opening a Support Case too.  ... View more

Hello, Internet router is directly connected to MX internet port. ... View more