Congratulations to everyone! Thank you for all your contributions! ... View more

I know your initial problem was resolved, but since you asked, you won't be able to console into any Meraki hardware. Local WebGUI (limited) and Dashboard only. ... View more

Glad you were able to get it squared away! ... View more

Not sure if ChatGPT could be considered a "Meraki Insider", but here is what it says... You are the one usually answering questions, so if you are asking the question then we know it's a stumper. Double kudos to the member with the right answer lol. "No, the Meraki MS130 series switches do not have full NBAR (Network-Based Application Recognition) support. NBAR is typically associated with Cisco's more advanced routers and some Catalyst switches that support deep packet inspection and application recognition capabilities.   Meraki devices, including the MS130 series, focus more on cloud-managed network solutions, providing visibility and control over network traffic but generally do not offer the same depth of application-layer traffic analysis as NBAR. Meraki switches do provide some Layer 7 application visibility and control features, but these are not as comprehensive as full NBAR support found in other Cisco products. For more advanced application recognition and management, you would typically look at Cisco products specifically designed for that purpose, such as routers with integrated NBAR or the Cisco Catalyst 9000 series switches." ... View more

I had ran into this same problem previously, with varying results from different firmware versions. @Ryan_Miles is accurate in that there is a very specific version that must be loaded. ... View more

Awe yiss!! Thank you to everyone who has made a difference here! ... View more

Did we ever find the root cause? ... View more

I feel using a VLAN as Ryan recommended would be the best way to go here without running additional cabling. ... View more

Have you ran the "cable test" function on each of those switch ports to identify a cabling issue like @DarrenOC recommended? ... View more

I have seen this before personally and had to go through the steps outlined below. Please keep this thread active and post back the results if you can so it can help others.   "Please note that 2FA removal requests cannot be resolved via our Support phone lines. For security purposes, a Meraki Support case requesting 2FA disablement must be open from the Meraki Support Page under the 'No dashboard Access?' section. " https://meraki.cisco.com/meraki-support/overview/ ... View more

Also, as a best practice ensure you have more than one admin account for your Organization to keep these issues from occurring in the future. ... View more

Out of curiosity @Ryan_Miles , let's say we remove the account altogether and they have access to multiple Organizations. Do we assume that we need to re-invite that account to each Org? ... View more

Really looking forward to a lot of these features. Thanks for sharing. ... View more

Thank you for posting your findings, was curious about this myself. Hadn't read the docs yet. ... View more

Good morning!  Have you used these same credentials before? Is it a local Meraki account or does your Enterprise use SSO?   If you have a local Meraki account I would advise going through the password reset process from the Meraki Dashboard login page.  If your company uses SSO there could be a few issues. Can you provide a screenshot of the error you are receiving? ... View more

My vote is against the plastic. These switches aren't cheap and I feel that these have the potential to break. I did see something similar from Patchbox the other day that could work for you. https://shop-us.patchbox.com/products/dev-mount-50-pack ... View more

@PhilipDAth great content and discussion. This is what these boards are for. Way better than just links to the KB articles.  ... View more

Thanks for sharing! This is very helpful! ... View more

Client page would be the fastest and easiest for sure. Just search for your host name or MAC as @Brash styes above ... View more

What @Brash said above. You’ll need to contact Meraki support. This is likely a feature that could be enabled in the future as this has been widely requested here in the community. ... View more

What is upstream of the switches? Router? Firewall? Any changes upstream? ... View more

Keep the fun coming! Love this! ... View more

Thank you and congratulations to everyone in the community! Well deserved. ... View more

We should see some improvements to RBAC within the year. This is a highly requested feature. ... View more