Is routing to 192.168.1.0/24 configured in Mikrotik? I was curious if there is a return path for communication. ... View more

You have a good friend! I wish you good results. ... View more

If the device is transferred from a friend to you, the original owner must deregister the device from the original owner's inventory (organization). If it is not treated as stolen, the license can be purchased from the distributor.   In my experience, I once bought a used device to try, but it was still registered in the original owner's inventory. That device is a paperweight. Incidentally, I tried to buy a license by contacting a distributor where personal purchase is available.   Please be careful not to get into trouble. ... View more

SD-Internet functions control traffic in Underlay (WAN1, WAN2). Until the SD-Internet feature was introduced, traffic control was focused on Overlay (Auto VPN Tunnel). This makes it a good companion feature to "Local Internet Breakout".   [Doc] SD-WAN Internet Policies (SD-Internet) - Cisco Meraki https://documentation.meraki.com/Architectures_and_Best_Practices/Cisco_Meraki_Best_Practice_Design/Best_Practice_Design_-_MX_Security_and_SD-WAN/SD-WAN_Internet_Policies_(SD-Internet)   [Requirements] * SD-Internet requires a Secure SD-WAN Plus license.   * You must make a request to support to activate SD-Internet.   * Supported MX models are limited.   > Supported MX models - MX64, MX65, MX67, MX68, MX75, MX84, MX85, MX95, MX100, MX105, MX250, MX450   > Unsupported MX models - MX50, MX60, MX70, MX80, MX90, MX400, MX600, vMX (all)   * A firmware version (16-X) is required. ... View more

I sometimes wonder if my interpretation is correct. It is difficult to confirm the operation of the license registration, so it would be better to check with Meraki sales. Hoping there is another better way. ... View more

I have experience upgrading from Enteprise to Advansed Security License using the Co-Term licensing method. When I selected "Renew my Dashboard license" the existing Enterprise License value appeared to be converted. Perhaps, with the Co-Term licensing method, the license expiration date is unified throughout the Organization regardless of license type, so the value of the existing license remains.   [Related document] Meraki Co-Termination Licensing Overview - Cisco Meraki https://documentation.meraki.com/General_Administration/Licensing/Meraki_Co-Termination_Licensing_Overview#Renewing_Your_Dashboard_Licensing > Renewing Your Dashboard Licensing > When a license key is applied using the Renew my Dashboard license operation, the organization’s licensing state updates to exactly match the device count of that license key, and any remaining time from previous licenses is kept and added to the new co-term date. For example, if an organization with licensing for 5x APs were to have a 2x AP, three-year license applied as a renewal, that organization would only be licensed for 2x APs for three years, plus the remaining time from prior to the renewal. In this instance, the organization would be 3x APs over the license limit, and therefore out of compliance. > > Note: The recommended practice for applying a renewal is to purchase a single license key that covers all devices currently in the organization for X number of years. Applying that license key as a renewal will then extend the organization’s co-term date by that many years while keeping the same license limit for devices.     In the case of PDL, the purchased license is simply added to the Organization. For example, I have separate Advanced Security License and Secure SD-WAN Plus License for MX67W. The license value is not converted. The license expiration date is also independent.   ... View more

The Co-Term licensing method offers two options.   * License more devices   Select 'License more devices' if you will be connecting more devices to the Meraki cloud.   * Renew my Dashboard license   Select 'Renew my Dashboard license' if you wish to extend your current expiration date without adding more devices. NOTE: selecting this option will replace your Organization's license limit to match the applied license key.       The "License more devices" option is selected when more devices are to be added.   If the number of devices is the same as the number of licenses purchased for upgrade purpose (Enteprise => Advansed Security), you should select the "Renew my Dashboard license" option.   However, since you are a PDL (Per-Device Licensing) method, this does not apply to you. ... View more

DevNet users can regenerate their API Key, so it may have been changed to a different API Key. ... View more

I am waiting for a response from support about a fix as well.   I marked the solution in terms of contacting support. Sorry for the confusion. ... View more

Client Balancing - Cisco Meraki https://documentation.meraki.com/MR/Other_Topics/Client_Balancing#Client_Balancing_Behavior_-_MR_29.X_and_Newer_Firmware > Client Balancing Behavior - MR 29.X and Newer Firmware   > An AP can only attempt to load balance the client or reject an association request two times for both active and passive client balancing.     I've been waiting for this feature! 😍   In high-density wireless environments with many Meraki MRs, Client Balancing may in some cases continue to reject clients. e.g. The wireless client goes to connect to MR#1 (reject) => MR#2 (reject) => MR#3 (reject) => MR#4 (reject) => MR#1 (reject) ... and so on.   It is good that a limit has been placed on the number of rejections. I hope to improve the wireless environment! ... View more

Unfortunately, the problem has not been solved.  😫   * There is no way to change the fact that the communication will be over the Internet because of Meraki vMX on AWS in my work environment.   * Other devices (e.g. IOS-XE) might be able to adjust this with a DPD (Dead Peer Detection) timer.    However, Meraki has been deployed. 💸    But we can't adjust the timer in Meraki...   It seems that I will probably have to accept this to happen. Personally, I want to check if another network device using the same internet connection would be more stable. ... View more

Very nice feature!     > Starting 9th August, the new wireless overview page can be enabled on select networks by reaching out to your Sales team.   For your information. According to support, it is currently only enabled on a per-Network basis. It cannot be enabled for the entire Organization. = Specify the target Network when requesting support. ... View more

The Peer is the MAC address of the Auto VPN Peer. Searching by Inventory makes it easy to identify the Peer. I think the reason it is not the name of the device is to uniquely identify it when the name is changed.   There may be a problem between the MX of the Network that is outputting that log and the Auto VPN Peer. Meraki MX's Auto VPN Tunnel Failure Detection is at 5 second intervals. Therefore, It is possible that the ISP did not detect the problem due to a short period of flapping. Incidentally I contacted support, but the detection interval cannot be changed.   For your information. In my work environment, Meraki MX & vMX are flapping to the point of concern. I think it is because we are using Internet connection and cannot control the quality. Personally, I would like to know if it is the same in other production environments. ... View more

Except for device-specific settings and so on, the settings menu is basically displayed on the Template side when a Template is used. (It may not appear in the menu on the Network side.) Therefore, if you set it up on the Template side and tie it to Network, it should work. ... View more

Are you talking about Client VPN (L2TP or AnyConnect SSL-VPN)? (It's not Site-to-Site VPN.)   I have a Z3. I have confirmed that Client VPN feature can be enabled for non-template. I haven't checked to see if Client VPN actually works because I haven't made it accessible directly from the Internet.   ... View more

As of August 2022, it was possible to get the change log via API.   [Configuration changes] *Equivalent to "Organization > Change log" Menu. Get Organization Configuration Changes https://developer.cisco.com/meraki/api-v1/#!get-organization-configuration-changes API: GET /organizations/{organizationId}/configurationChanges [View API request] Get Organization Api Requests https://developer.cisco.com/meraki/api-v1/#!get-organization-api-requests API: GET /organizations/{organizationId}/apiRequests ... View more

If you are talking about Static Route to the Uplink side of Underlay, Meraki MX is not supported. ... View more

Support says the technical team is working on it. (2022-08-02 11:18 JST / 02:18 UTC) ... View more

Thank you for your reply. I have contacted support. ... View more

I want important information recorded in the history.   I have previously told the customer with old information (150 prefixes). If there is no record history, then it is assumed that I lied. So I wrote the information to preserve the evidence. ... View more