New articles:
Cloud-Native IOS XE
Cloud-Native IOS XE Overview
Cloud Native IOS XE FAQ
Migration from CLI-managed Catalyst Switches to Meraki-managed Mode
Upgrade Steps for Cloud-managed Catalyst Switches
Change: New articles.
XDR
XDR Quick Start Guide
XDR User Guide
Cisco XDR FAQ
Change: New articles.
Meraki and Starlink Deployment Guide
Change: New article.
Cisco Meraki MR46E VusionGroup ESL Specifications
Change: New article.
Seamless Meraki Integration with Cisco Spaces
Change: New article.
FIPS 140 Configuration Guide for Cisco Meraki
Change: New article.
Cisco Administrator Access
Change: New article.
Root Cause Analysis - Alert Workflows (RCA)
Change: New article.
Call Me Now
FAQ for Call Me Now
Change: New articles.
Cloud Monitoring for Catalyst:
Adding Catalyst 9800 Wireless Controller and Access Points to Dashboard
Change: Added "Meraki Offboard EEM Script".
MG:
Cisco MG52 AT&T eSIM Activation FAQ
Change: Added sections "Initial Bootstrap Data FAQs" and "Troubleshooting FAQs".
MX:
Route Table
Change: Added "Hovering over the "i" next to the subnet will expose additional attributes such as AS Path, Origin, Local Preference, Next Hop and historical connectivity information."
Border Gateway Protocol (BGP)
Change: Added "BGP is not supported for template networks."
MX95/105 Datasheet
Change: Updated "Stateful firewall throughput" and "Maximum VPN throughput".
Port Forwarding and NAT Rules on the MX
Change: Added section "Port forwarding/NAT rules and Inbound firewall rules".
Connection Monitoring for WAN Failover
Change: Added "Hence, a soft failure will be quicker in case the ARP test to default gateway fails before ICMP or the HTTP test."
MX64 and MX65 Overview and Specifications
MX67 and MX68 Datasheet
MX75 Datasheet
MX75 Hardware Installation Guide
MX84 Datasheet
MX85 Datasheet
MX85 Series Hardware Installation Guide
MX95/105 Datasheet
MX95/MX105 Series Hardware Installation Guide
Change: Updated "Recommended Device Count".
MS:
SmartPorts
Change: Added note "SmartPorts are currently not supported in networks enabled for SecurePort."
Catalyst 9300/X/L-M Series Installation Guide
Change: Added description for the "Active LED" states.
Adaptive Policy MS Configuration Guide
Change: Added "VLAN to SGT mapping feature is available on MS390 and Catalyst switches in managed mode from firmware CS 17.1.2.1 and above."
Advanced MS Setup Guide
Change: Added "If a Native VLAN is specified, ensure that it is also added to the Allowed VLANs configuration."
Getting started: Cisco Catalyst 9300 Management with Meraki Dashboard
Change: Added announcement notice about Cloud-native IOS-XE public beta.
Change of Authorization with RADIUS (CoA) on MS Switches
Change: Added PoE behaviour for Port Bounce (Catalyst-based switches: Bounces PoE on the port. MS-based switches: Does not bounce PoE on the port.).
MR:
Configuring RADSec (MR)
Change: Added "'RADSec Keep Alives' is a Meraki Dashboard Early Access feature. Before changing this configuration, you need to opt into Early API Access."
SSID Tunneling and Layer 3 Roaming - VPN Concentration Configuration Guide
Change: Added "This is not a recommended deployment, but the tunnel will form. Please note that there might be some MTU issues with this approach."
AI-RRM
Change: Added note "Currently AI-RRM is in Early Access phase, available in US and EU region. APAC regions and Canada doesn't have AI-RRM service during this Early Access phase and will be introduced when solution become generally available."
Meraki MR License Guide
Change: Added AI-RRM and Intelligent capture.
MR Meraki RADIUS 2.0
Change: Added Called-Station-ID and NAS-ID attributes "AP LAN IP" and "AP Public IP"; added note "When 802.11r is enabled, the available NAS-ID options will be limited to specific attributes to ensure the network remains stable."; added section "Device IP set as NAS-ID".
Wireless Mesh Networking
Change: Added CW9163E and CW9166D1.
VusionGroup Electronic Shelf Labels (ESL) Integration with MRs
Change: Added Bluetooth ESL mode.
NAT Mode with Meraki DHCP
Change: Added "Group Policy 'Security appliance only' settings" to section "Common Problems".
Understanding and Configuring Management VLANs on Cisco Meraki Access Points
VLAN Tagging on MR Access Points
Change: Added note about native VLAN configuration between the access point and upstream switch.
SM:
Systems Manager Firewall Rules
Change: Added "*.meraki.net" for Meraki-hosted Content.
MV:
MV23 Series Datasheet
MV73 Series Datasheet
Change: Added "MT Gateway Support for all MT sensors".
Meraki Vision Portal Changelog
Change: Added release notes for up to v1.23.0.
MT:
Sensor Alert Profiles
Change: Added note "MT20 will log all door opens and closes events, the behavior cannot be modified."
MT10 Installation Guide - Temperature and Humidity
Change: Added MV13/M, MV23M/X, MV33/M, MV63/M/X, MV73M/X, MV93/M/X and CW9163E-MR.
General Administration:
Getting started on Packet Captures with Wireshark
Change: Added references to free online training courses on the Meraki Learning Hub.
Active Directory Issue Resolution Guide
Change: Added "If VPN mode is disabled for all VLANs, the WAN appliance will use a 6.X.X.X source IP address to communicate with the AD server."
FIPS 140 Devices and Firmware for Cisco Meraki
Change: Added note "Any Meraki MX/Z Series devices not included in the list above is not FIPS compliant."; added MG52E; updated FIPS 140-2 Compliance Firmware for MX.
Using the Cisco Meraki Device Local Status Page
Change: Added behavior of the Local Status Page on Catalyst 9300/X/L-M series switches for both monitored and managed mode; added "Starting in MS17+, MS devices will now support HTTP CONNECT proxy."
Meraki End-of-Life (EOL) Products and Dates
Change: Updated the End-of-Sale Date for MG21-HW-WW and MG21-HW-NA to Mar 18, 2025.
Locating the MAC Address of Cisco Meraki Devices
Change: Added note "Meraki WAN appliances and switches configured in warm spare will also use virtual MAC addresses."
Using the License Calculator
Change: Added "For additional regions, navigating to the license calculator can be achieved by replacing .com with the corresponding extension for your dashboard region."
Meraki Subscription Licensing Overview
Change: Updated availability "Subscription licensing is available for new and renewing customers globally except in Brazil, India, Russia, Belarus, and China."
EU Cloud Configuration Guide
Change: Updated hosting region for Europe to European Union.
Dashboard Data Storage Privacy and Security
Meraki Cloud Architecture
Change: Added France.
Information for Cisco Meraki for Government users
Change: Added "MG, YouTube Content Restriction, Web Search Filtering, Cisco Secure Malware Analytics Integration (formerly know as Threat Grid) and Adaptive Policy" to Supported Features; added "vMX, Trusted Traffic Exclusions powered by NBAR, Umbrella DNS Integration, ThousandEyes Agent Integration, MX SD-WAN+, Cisco Catalyst Monitoring, Z4 Series and Meraki Mobile App" to Unsupported Features.
Adaptive Policy Configuration Guide
Change: Updated note about the Infrastructure Group description "The default value is 2 and unless necessary to integrate with other deployments, it is not suggested to modify this value. If it is necessary to change the Infrastructure group, be careful if modifying in production as a mistake can isolate the network device's originated traffic if an upstream device does not permit the traffic due to policy."
Manually Integrating Cisco Umbrella with Meraki Networks
Change: Added "An existing license to use Cisco Umbrella" to Licensing Requirements.
Dashboard Access Restricted Due to IP Address Geolocation
Change: Added note "Devices in restricted countries and regions should also not be expected to operate online and connect to the Meraki cloud."
Configuring SAML Single Sign-on for Dashboard
Change: Added "Additionally, when the SAML assertion is failing, kindly check for spelling mistakes or leading white spaces in the defined roles which are the most common mistakes."
Alerts and Notifications
Change: Added "The Account Status of the added Network admins need not be in a verified state to be a recipient of these alerts."
Two-Factor Authentication
Change: Added "When Two-Factor Authentication is not enabled, the user will see a banner "Two-factor Authentication is not currently enabled on your Meraki Dashboard account. For an extra layer of security, we recommend enabling it at your earliest convenience." Clicking on the [x] button will not permanently remove the banner."
Assurance Left Navigation
Change: Updated section "Context".
... View more