Meraki

BlakeRichardson · ‎Dec 16 2024

@aaaomt You need to provide more information. Have you tried turning it off and back on again?

BlakeRichardson · ‎Dec 15 2024

Thanks for the update and suggestion but no I'm not using that setting.

BlakeRichardson · ‎Dec 15 2024

A bit of a rant here, last few days of work with a lot going on and I have 20 iOS devices I need to refresh so I erased the devices using the below options. Now the command went through but not correctly. All it did was remove the enrolment profile and not erase the device. So now I have the manually erase each device using configurator and start from scratch. It's my fault for trusting the system but a word of warning for anyone else looking to use this feature test it with a single device first. Note: All devices running iOS 17 as required.

BlakeRichardson · ‎Dec 12 2024

Interesting, I have the same issue on my MacBook Air with MacOS 15. The time is took to draw correctly was significantly less though.

BlakeRichardson · ‎Dec 12 2024

@edgepro I would suggest instead of using bluetooth based IOT using a Wifi based IOT system. https://security.gallagher.com/Solutions/Access-Control

BlakeRichardson · ‎Dec 12 2024

Whenever I look at the reports page for my MT sensors the top portion of the page has formatting issues and if I leave it for a few minutes it comes right on its own.... I'm using a Mac with Safari 18.1.1 When the page first loads After a leaving it for a few minutes.

BlakeRichardson · ‎Dec 12 2024

I like this clever thinking although it also means another job given to IT when office lights stop working.....

BlakeRichardson · ‎Dec 12 2024

I would not recommend relying on a wifi based IOT sensor for fire protection, get a proper hard wired system that is serviced regularly. Our fire protection system sends me an SMS when a panel is activated and when it's been restored. Had a callout on Wednesday just been and response time from fire service was 11 mins from activation to panel reset.

BlakeRichardson · ‎Dec 11 2024

I found the gnome https://community.meraki.com/t5/Smart-Cameras/rename-camera/m-p/254157#M3947

BlakeRichardson · ‎Dec 11 2024

How many client devices is the MX supporting, it sounds like it's being over utilised. Do you have any site to site or client VPN connections?

BlakeRichardson · ‎Dec 11 2024

😂When it rains it pours ( notifications that is), I have the same issue My other issue is the MV flagging motion outside of my area of interest which on a busy street makes reviewing footage slow as everything is captured.

BlakeRichardson · ‎Dec 11 2024

Like the idea but for me the data on this page doesn't match data on other pages.

BlakeRichardson · ‎Dec 8 2024

As long as your client devices and switches all have unique IP addresses you should be OK.

BlakeRichardson · ‎Dec 8 2024

Well done everyone and @cmr top effort, you have been busy!

BlakeRichardson · ‎Dec 8 2024

@techfldusd You are better to be blocking applications on a firewall rather than on the access points themselves.

BlakeRichardson · ‎Dec 3 2024

You could look at having cages installed around the cameras although this could affect the view.

BlakeRichardson · ‎Dec 3 2024

I don't believe Meraki officially offers replacement parts. If the camera has an issue contact support and arrange an RMA. If the camera has been damaged then you are most likely on your own.

BlakeRichardson · ‎Dec 3 2024

Is it just the link going down or the whole switch? Make port scheduling isn't enabled on the port.

BlakeRichardson · ‎Dec 3 2024

Ideally you should be managing Apple devices via an MDM, with managed devices you can disable Private MAC. If the devices are BYOD of some description the only resolution is make sure the class of network you have chosen can handle the amount of devices. https://support.apple.com/en-nz/102509

BlakeRichardson · ‎Dec 2 2024

What is your wifi coverage like and what method of authentication are they using?

BlakeRichardson · ‎Dec 2 2024

Well done everyone. Nice work as always! I had to laugh this banner make it looks like the winners are retirees

BlakeRichardson · ‎Dec 2 2024

If you have a Apple USB ethernet adaptor plus a Apple lightning to camera adaptor you can make a makeshift ethernet adaptor

BlakeRichardson · ‎Dec 2 2024

If you use a print server your clients communicate with the print server and not the printers directly. The print server passes any jobs onto the appropriate printer, this is a much more secure option and like @Brash this is what I use.

BlakeRichardson · ‎Dec 1 2024

I would create a firewall rule that only allows the clients to access the printer/s that are needed and I would lock the rule down to use whichever protocol you use for printing. If you want to ensure things are secure make sure you enable IP filtering on the printers themselves.

BlakeRichardson · ‎Nov 28 2024

Have you read this documentation as there are variables. https://documentation.meraki.com/General_Administration/Cross-Platform_Content/Clients_Usage_Page_Overview#:~:text=Clients%20list%20data%20is%20aggregated,automatically%20refreshed%20every%20few%20minutes.

About BlakeRichardson

BlakeRichardson

Community Record

Badges