Meraki

thomasthomsen · ‎Jul 23 2024

You write "migration" ... do you mean converting these APs to be running on the dashboard without a local WLC ? Then no, that is only for the CW916x APs (where you can actually start the migration on the 9800 WLC). For monitoring the 9800 WLC with the C9100 APs on the dashboard yes, that is supported as mentioned by others.

RaphaelL · ‎Jul 21 2024

here is the doc : https://documentation.meraki.com/MX/Networks_and_Routing/Dynamic_Protocol_Status

Tribbio · ‎Jul 18 2024

Yep I know ahahha. I'm talking abt freeradius, for eduroam service. If u know this service.

PhilipDAth · ‎Jul 17 2024

Site to site VPN?

Brash · ‎Jul 16 2024

It'll take a bit of getting used to, but I have no issue with it. Especially since the option to disable it is still there. And to be honest, I'm impressed that an accessibility change is being pushed by default with the ability to opt-out rather than needing users to opt-in. 👏

Wifikohai · ‎Jul 16 2024

Hi, Does anyone know if I add an Ip addres on Trustestes/network traffic. Traffic on any direction (from and to this host/network) won't be analyzed by the IPS?

RaphaelL · ‎Jul 15 2024

I just checked on of my network that has the legacy NAT Exception option and the Remote status page option is visible. I don't know why it is not showing in your case. Edit : Enable or disable access to wireless et switch device status pages at http://[device's LAN IP]. Forget the "Remote device status pages". Just try to disable the local status page and check if you still have the page accessible.

RaphaelL · ‎Jul 15 2024

Great article ! Bon travail Xavier !

AlBalooshi · ‎Jul 15 2024

Congrats everyone, this is a very beautiful product.

rhbirkelund · ‎Jul 14 2024

I'm not that versed in Postman, so unfortunately I can't say. However, I seem to recall there are some looping functionality in Postman, but I'm not sure. You're best is to look at some of the guides and documentation for Postman.

kchand · ‎Jul 11 2024

Hello Mauro, Replacing your MX85 with MX84 will not affect your configuration. However, please keep in mind that the maximum runnable firmware version for MX84 is MX18.107.10. So, any new features available from the MX18.211+ version will not be available while using the MX84. Also while moving the cables on the LAN interfaces please ensure you are plugging into the right LAN ports and enabe the site to site VPN

MisG · ‎Jul 9 2024

Thanks so much 🙂

John_on_API · ‎Jul 9 2024

Thanks for sharing this request! Please work with your account rep to open a feature request at your convenience.

John_on_API · ‎Jul 9 2024

If you are experiencing this issue, please contact Meraki Support to resolve.

Brash · ‎Jul 8 2024

Closing off my experience on this. The MX75 I opened a support case for rebooted for a different reason. However support confirmed that a different MX75 had encountered hardware panic reboots and required replacement.

IvanJukic · ‎Jul 8 2024

Hi @Martinsen , As @PhilipDAth has mentioned. The best option is to check the local status page on the switch. If all ok, then factory reset them.

alemabrahao · ‎Jul 8 2024

It's working normal here.

GiacomoS · ‎Jul 8 2024

@nb12345 , could you DM me a link to your Dashboard or the serial number of the MX please, curious to see what's going on. Many thanks! Giac

rhbirkelund · ‎Jul 8 2024

Apologies, this was the video I was talking about where you very short can see the Org-Wide L7 rules; https://youtu.be/pFwMPxDjTQ4?si=I0ad6waIu5yUW9fO&t=1185

PhilipDAth · ‎Jul 8 2024

A wild shot in the dark - some carriers support baby giant packets. You could try asking support to INCREASE the MTU on the MG41 from something like 1500 to 1508 bytes (being the additional size of PPPoE header). If it works you'll get a 1500 byte clean MTUs. Otherwise, it will completely break it.

rhbirkelund · ‎Jul 5 2024

I guess it depends on how well you want to play with Meraki. In the end Meraki is all about RESTful calls, whether it's the API or the Dashboard itself. If you want to abide by the rules, then no, there isn't an endpoint to change the Splash Page Theme to Fluid. But if you're feeling a bit rebelleous, there are ways around... Hint: cookies are delicious...

alemabrahao · ‎Jul 5 2024

I would suggest you open a support case.

cmr · ‎Jul 4 2024

There was an attempt to provide the switch port data for MXs a few years ago. It only lasted on the dashboard for a couple of days and never made it to the APIs due to numbering errors that were never resolved. An example of this is the MX75 where ports 1-3 are WAN ports so port 4 is actually called LAN port 0 in the back end, with port 5 being LAN 1 etc. I don't know why they didn't fix it and republish the page as it doesn't seem an insurmountable issue to me.

vijaykumar · ‎Jul 4 2024

Thanks for your response. I will test it in MW and monitor it. Thanks again.

Saf · ‎Jul 3 2024

Ah awesome, thanks for the confirmation @RaphaelL!

About RaphaelL

RaphaelL

Raphael Letourneau

Community Record

Badges