logigng into the meraki dashboard it works for everyone in the company entering the mobile authenticator apps. I have tried resetting the passwords several times. It allows me change the password. but when I try on the new password it is the same issue. ... View more

Hooray, the badging issue is resolved, and you should have received your September Member of the Month badges just now!! Thanks for your patience all.  ... View more

Helpful info.  In my case, not all inventory items were expired for most orgs, but I have a couple that I can delete completely with this info.  Thank you. ... View more

I know your initial problem was resolved, but since you asked, you won't be able to console into any Meraki hardware. Local WebGUI (limited) and Dashboard only. ... View more

Happy birthday! What a year and what a blast! Thank you @AmyReyes and @CarolineS you are the best! Also would like to thank all the heroes dedicated to this community! Keep up the good spirit everyone! ... View more

Well I'm a little skeptical what an AI can offer who just gets it's information on any other public website 😉 I'm hoping since the MS130X/R series have some sort of advanced ASIC to support Adaptive policy it would also support NBAR at least for fingerprinting traffic. My question originates from the time you could not have non-NBAR and NBAR capable devices on the same network while NBAR was enabled.  Since newer networks are usually combined even MS210's with Wi-Fi 6(E) hardware it still can use NBAR on the Wi-Fi and MX side.  But this would cause inconsistencies in the traffic analytics. ... View more

I had ran into this same problem previously, with varying results from different firmware versions. @Ryan_Miles is accurate in that there is a very specific version that must be loaded. ... View more

I asked via my ticket, but I got a pretty general answer. Not a direct quote:   Engineering implemented some back-end changes which inadvertently irritated SAML. The changes were backed out, which resolved the problem. ... View more

Gigabit connectivity requires all four pairs, if one is faulty then only 100Mb can be reached.  If you bypass the PoE adapter and connect a laptop or similar, does it connect at 1Gb?  What model is the switch?  What PoE adapter are you using? ... View more

Resolved for me now (I didn't check over the weekend), so hopefully for you? ... View more

Also, as a best practice ensure you have more than one admin account for your Organization to keep these issues from occurring in the future. ... View more

Out of curiosity @Ryan_Miles , let's say we remove the account altogether and they have access to multiple Organizations. Do we assume that we need to re-invite that account to each Org? ... View more

The intellignent capture on MS is very impressive.  I'm not sure if using Wireshark will even be required anymore. ... View more

Thank you for posting your findings, was curious about this myself. Hadn't read the docs yet. ... View more

10 more days, I am getting very excited. ... View more

Go to the switch, click on the port and look at the clients. If the client is a bit more silent then you could go to the mac-address table in the tools page and filter on port. In the extreme case you have very quite clients you could add port-security sticky to that port and just see after a while what mac addresses were added on the port. ... View more

Yes it will be added and the GUI in dashboard will even feature a graph over time for all the values (RX, TX, temp, current). ... View more

yea, iv seen those too but are expensive. Apparently these duo rackstuds are made from exceptionally strong plastic that is often used as a metal replacement. The sheering load strength is 150Kg. Also apparently the levering force of a meraki switch when mounted is about 30kg so they should be ok. But i will still be very mindful about exactly where i use them until I am 100% confident ... View more

@PhilipDAth great content and discussion. This is what these boards are for. Way better than just links to the KB articles.  ... View more

What @Brash said above. You’ll need to contact Meraki support. This is likely a feature that could be enabled in the future as this has been widely requested here in the community. ... View more

Wow. Thanks team! and congrats to everybody else!  ... View more

Hi @Martinsen , As @PhilipDAth  has mentioned. The best option is to check the local status page on the switch. If all ok, then factory reset them. ... View more

These threads just solidified that I will work on a new solution for my sites since I am down to the last 3 months of my current licensing. I was considering switching over to Meraki, but I cannot take the risk that this could happen to any of them. I will try the Onada solution and see where that takes me. Thanks all for the info. ... View more