Even expanding to a whole week shows no change in the clients list ... View more

I'm seeing similar issues, oddly enough I can see a ton of wireless devices on non-Meraki APs but 95% of my wired devices don't show unless I drill down to the port details but when I click on the clients there it just takes me to a page saying the client wasn't found. Very odd indeed. I opened a thread just a bit ago before I saw this one 🙂 https://community.meraki.com/t5/Dashboard-Administration/Dashboard-Client-Display-Issues-Catalyst-Monitored-Switch/m-p/234958#M8214 ... View more

Man, what a crazy conspiracy theory. 😂 ... View more

Same here, I tried clearing browser cache and cookies too but same thing so something definitely broke with the new changes. ... View more

Update from Meraki support.   Hi Blake, Thank you for contacting Cisco Meraki Support! I can confirm that this is unexpected behavior that our development team is currently investigating further in regard to the 5 free MT licenses in PDL organizations not showing as properly assigned in the Overview/Devices tabs. At this time, there is no ETA on when this will be resolved, but I will continue to monitor the progress and provide you with an update as soon as I have more information.     I will update again once there has been a resolution.  ... View more

I was able to fix the problem by upgrading to v18 and change Client tracking to "IP Address." The problem was the new Content filtering changed in v17 was not working well with my internal L3 routing.  ... View more

Just checked in my dashboard and it seems fixed as well for me.  I still haven't gotten any response to my case from them however. ... View more

Called support and because we have too many clients on the MX67, not much troubleshooting on their side.  They even saw how it performed running 18.107.2 and then how much better it was on 16.16. So now not sure if I should upgrade the firewall to a bigger version, or just go look at something else as I believe they use the same firmware for all the MX's. ... View more

Looks like there might be a doc issue at least. I opened a case and support was surprised to say the least that the docs call out IPv6 SVIs 🙂 Still waiting to hear more though so we'll see what happens. ... View more

Looks like this is now available to enable. I was able to toggle it on a couple networks without issue late yesterday. ... View more

Upgraded a couple test switches to 16.1 but still cannot enable the DHCPv6 RA Guard Early Access setting for some reason. ... View more

Thx, I tried, it seem's ok! ... View more

After ~ 3 hours on the phone with Meraki and sharing the information provided by @IDV , @Raphael, @dgander , @dade80vr  & @dade80vr we have a "bandage" to resolve this until an update to fix it is released.  I was informed that Meraki is aware of the issue and is working on a solution.  No ETA as to when the actual fix will be known.  Meraki also stated that this is only affecting MX84's.  I suspect it may affect other models as well that the setting listed below is available on.   Solution:  Disable Web Cache and reboot router. Security & SD-WAN -> SD-WAN & Traffic Shaping   Unfortunately a reboot is required for the change to take effect.   I hope this helps anyone currently having the issue.     ... View more

Posting if this helps others, upgrading MX units to 18.105 which only have cellular/4G internet (ie, no ethernet internet connectivity) there appears to be a bug which the unit reports on the dashboard as upgraded to 18.105 however the device goes offline for 15 minutes every 2 hours. Meraki support engineer confirmed the device was stuck in a upgrade loop and was actually still running 17.10.2 firmware even though the dashboard says its updated. Telling the MX to reboot via the web dashboard 'fixes' the issue for a few hours before it comes back again. The actual fix is to pull the power out of the MX and reconnect, the hard power off/on appears to force it to update correctly. ... View more

I guess they went ahead and released 17.10.2 anyway and I'm having the same issue at two of my client sites. Sigh. MX64W: LAN is fine, wifi is trash. ... View more

Iperf3.1.3 in terminal direct to provider’s servers. (Breezeline, old miami Atlantic broadband).  I’m still fiddling so we see what I find out.  It’s probably something simple, but no log changes have been made to the threat center setting since end of 2021. It’s also happening at another Propery in network on the organization that also has an MX-85.  I have some unopened spare MX-85’s that I’ll probably swap in with it’s default configuration out of the box. And we see what happens.  Then I’ll do a line by line compare of configuration if indeed the out of box one is back running 950+   ... View more

First I strongly recommend downgrading to version 16.16.6, if you look we have several other threads open related to instabilities from version 17.x and version 18.x is a Beta version yet. Meraki even removed version 17.10.1 from the stable release list. ... View more