Here are the more detailed docs I was thinking of.  You should be able to access with reseller CCO ID:   https://www.cisco.com/c/dam/en/us/products/se/2018/4/SC_Ops/Meraki_Now_Service_Offer_Sales_Playbook.pdf   https://www.cisco.com/c/dam/en/us/products/se/2019/4/Collateral/meraki_now_solution_guide-_aka_AAG-032719.pdf ... View more

Hello @Jeizzen    It is not viewable unfortunately. I would recommend submitting a feature request to be able to see it like for client VPN ... View more

Ah very nice!    Agree regarding the pasting option @BrechtSchamp  ... View more

@Mrjkcs wrote: when i email them regarding this matter they only pass me to an meraki support to solve these matter So what does Meraki support tell you?   I would think either 1) They tell you it is, in fact, already registered to another organization or 2) they recognize an issue they can fix for you.   If #1 I guess you should get your money back and send the gear back to where it came from.   Best. ... View more

The Cisco Aironet AP's with WLC do support wireless mesh with ethernet bridging and VLANs. ... View more

Many thanks. papertrailapp.com  is very helpful ... View more

Yes, to the storage devices for the security cameras ... View more

So MS acts a bit like Portfast, just with less risk of loop and a bit more intelligence. ... View more

It would be pretty hard do define overall best practices, but I have been thinking about doing this for my home network for security concerns.  With my ever growing collection of "smart" devices and speakers I am concerned with the attack vector that could allow access to my network through a compromised or backdoored smart switch/speaker/light/camera/lock/thermostat, etc.  The hard part is really figuring out what inter-VLAN access might be required or desired to operate.  Each device can have different requirement and might be difficult to work with when on a different VLAN than the one used for general internet access.  Good luck.     ... View more

Search for the word "firewall" at this url.  It has a couple of suitable scripts that you would start with. https://developer.cisco.com/codeexchange/github/repo/meraki/automation-scripts/ ... View more

The MX can only say that it has had a loss of service.  It is not possible to say what upstream (such as the ISP router)  has failed. ... View more

Okay, if your VLANs on the switch are sorted the tagging is enabled on this port it should just be a matter of setting up the appropriate virtual interfaces on the ethernet device. This is pretty much up to the system admin of that system. If they said it worked on a different brand of switch then you could try using that. But personally, I have not had any issues with Meraki or CISCO switches and this kind of tagging to a device (even using VMWare / other virtualisation software).   I would suggest that if you have a macOS device floating around, (BSD backend) not sure what system you are using. Then you could try setting up VLANS on the ethernet interface. It is straight froward and you can do it all from the GUI (network settings). Could be worth a try! ... View more

Still broken ... View more

While I do work for Meraki, I have no specific answer to this, at this time - but I would take a look at the kind of performance available from the likes of MX67/68, within the MX Sizing Guide - and wonder whether you could actually gain anything from the extra bandwidth that WiFi6 might offer..?   If it were me, I'd be choosing my MX and my preferred MR access point separately.  This also allows you to put the AP in the best place for coverage, leaving your MX safely in a rack or similar - plus you could deploy more than one AP, to have a fully roaming WLAN, should you need to extend your coverage. ... View more

No, you cannot 'upgrade' a license between different models and get a pro-rated time period, like when going from Enterprise to Adv Sec. You would need to purchase a new license for the MX84. ... View more

MA-ANT-21 in operation on the bottom R connectors on 5 MR74s all over my property which seem to be doing ok. Why would you need to use the dual band variant on a single band radio?  ... View more

I would check the handoff between AP's and then focus on the RF frequencies and tweaking them. ... View more

Hi Philip,   Just to confirm again, the MX250 WAN port supports a 1 Gbe SFP copper Module if the ISP provides a 1Gbps ethernet handoff correct? ... View more

That is understandable!   Hope you get it sorted. ... View more

Hi Richard,   the "default" traffic shaping rules were not there before, therefore we had to create them manually.   Cheers, Ben ... View more

Yes everytime I get gear quoted power cords are always on the quote as well. I opt not to get them (I am a customer not a reseller) as we always have power cords on hand.   The bonus of Meraki power cords is they come in a nice little cloth bag which is useful to store things in.  ... View more

In my experience whitelisting these ID events doesn't work very well or quickly.   Your best bet is start by changing the ruleset to balanced instead of security. The next option is change the mode to detection. Then it pinpoints which part of ID is detecting/causing it.   The other thing you might check is AMP settings.   Also if you can provide the SNORT link to the vulnerability it is detecting     ... View more

I have done this before with MR16s, MR18s and MR20s. It works fine. Access points in general are somewhat directional so with them pointing at the floor you probably will not get the best coverage, however if it is your only option and you have enough points to cover the area needed then it will work.   Phil ... View more

Please contact Meraki Support and they will be able to advise or enable this feature (if it exists). ... View more

@nyuszy wrote: This is a shared environment, 2.4 GHz is so much infected that I don't want to enable it all anyway. Anyway I'd consider doing this, but there's nothing like that officially supported for MR74, and a pair of ANT-20 for $199 list price is too much for this. $129/pair here: https://merakinow.com/products/ma-ant-20   I know it is expensive, but may be worth it for full Meraki support..     ... View more