Meraki

MarcP

Honestly, I don't have any goals this year. There are directions I'd like to go in, but whether it works out, you never know beforehand 😉 I'm just going to let things unfold this year. That makes it all the more exciting, haha. Just do what you feel like doing, both personally and professionally, and something good will always come of it.

MarcP · ‎Nov 5 2025

Or: https://community.meraki.com/t5/Wireless/Block-mac-address-in-SSID/m-p/152925#M21208

MarcP · ‎Nov 5 2025

As mentioned in my first response: https://documentation.meraki.com/MR/Design_and_Configure/Configuration_Guides/Encryption_and_Authentication/IPSK_with_RADIUS_Authentication

MarcP · ‎Nov 5 2025

Don´t get your question... Maybe you are searching for this? "Identity PSK without RADIUS Devices are assigned a group policy based on its passphrase"

MarcP · ‎Nov 5 2025

Antenna Patterns: https://www.cloudwifiworks.com/mr33.asp https://www.cisco.com/c/en/us/products/collateral/wireless/catalyst-9100ax-access-points/wireless-9172-series-access-points-ds.html?utm_source=chatgpt.com#AntennapatternsCiscoWireless9172I

MarcP · ‎Nov 5 2025

Having a look into details, seems like the different antennas/antenna design can be a problem. I would disable 6GHz, try to lower "max Tx Power" on 5GHz APs mounted under the ceilling (straight)? Maybe the heatmap shows some more details, regarding to placement.

MarcP · ‎Nov 5 2025

Anyone else having Problems reaching the dashboard? DNS_PROBE_FINISHED_NXDOMAIN

MarcP · ‎Nov 3 2025

Anyone else having the problem? I switch to darmode, all good. Refreshing the site ends in a reset to light mode, but still showing dark-mode.

MarcP · ‎Nov 3 2025

Just tested a bit, wasn´t too bad. Like health status was correct bound networks to templates and how many bound to each template. A bit bad was, AI Asstitant was not able to show the template name, only the template ID.

MarcP · ‎Nov 3 2025

I just use the actual adress. But I always use florrplans and place the devices where they are. Also Tags are usefull for me. Adress itself is just important, for me, to see the organization overview, als is green on the map (especially for the cio)

MarcP · ‎Oct 30 2025

Don´t see a point to do so anyways, haha Whats the use-case? Think about cloning the network if API is too much.

MarcP · ‎Oct 30 2025

You could export the config through API... (?)

MarcP · ‎Oct 29 2025

Just send a pic where you typed in the Ports @Jayt asked for, thats it, included where. Then you got the solution for him 🙂

MarcP · ‎Oct 29 2025

Made some research as well, but wasn´t able to find a SKU/Modelnumber like for others, MA-MNT-MRxx Maybe reach out to your sales rep is an option, if no other here has got a suggestion. If you have a 3D-printer you can maybe print it 😄 (wasn´t able to find a template 😉 )

MarcP · ‎Oct 28 2025

Only way is to verify all over again... MX port and DHCP settings, MS´s uplinks and MS-Port to MR. Verify the access control: Verify MR´s Port:

MarcP · ‎Oct 27 2025

Got the correct firewall ruleset? you may share some more information. You surely will get help, but more details needed for us. Feels like, as @DarrenOC said, you want others to complete your tasks 😉

MarcP · ‎Oct 27 2025

interesseting, requested acces 🙂

MarcP · ‎Oct 21 2025

As far as I know, port forwarding does not work through auto-vpn. At least in the past, when I tried it - long time ago. Maybe you got a public IP/dyndns on MX2 site and you can configure it like this.

MarcP · ‎Oct 20 2025

Opened a case at the same time and already got the info I need to remove the MS/MR from the network and then add it to the destination network. Of course, some settings will be lost and I need to reconfigure afterwards. Both networks are combined networks. May would have work when this wouldn´t be the case.

MarcP · ‎Oct 20 2025

They are already bound to the same config template. I want to merge two networks within the same Template configuration.

MarcP · ‎Oct 20 2025

Hi all, I´ve got two networks, within the same organization. Both networks are bound to the template. Now I want to merge both networks two one of them, as there has been a change and they have the same subnet now. Both have got a MS and MR each. When selecting the MS or MR in the overwiev and click "move" no other networks are shown in the list. Do I need to unbind one of the networks and merge it afterwards? There are no special settings within the networks. Thanks for your help, regards Marc

MarcP · ‎Nov 14 2024

Hi, anyone else having trouble accessing dashboard.meraki.com ?

MarcP · ‎Sep 8 2023

33 Switches (couple of stacks) , 150 Accesspoints. But regarding to your posts, decided to put all in one network 🙂

MarcP · ‎Aug 1 2023

Hi @BlakeRichardson , got a further question on this... Nearly the same question as above, but this time there is already a network running and now another building is coming in with its own corestack, switches and accesspoints. Existing network/building and new building are connected to each other. The new Corestack will get its uplink through the existing corestack. Is there a best practise for this? All in one Network or a new network for the new building? It may be more clearer if I have to networks, but as it is at the exact same address and even connected between each other I´m not sure what the best way is. Thanks, regards Marc

MarcP · ‎Aug 1 2023

Hi @GreenMan , got a further question on this... Nearly the same question as above, but this time there is already a network running and now another building is coming in with its own corestack, switches and accesspoints. Existing network/building and new building are connected to each other. The new Corestack will get its uplink through the existing corestack. Is there a best practise for this? All in one Network or a new network for the new building? It may be more clearer if I have to networks, but as it is at the exact same address and even connected between each other I´m not sure what the best way is. Thanks, regards Marc

About MarcP

MarcP

Community Record

Badges