Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About MarcP
MarcP
Kind of a big deal
Member since Nov 22, 2018
Nov 15 2024
Community Record
551
Posts
279
Kudos
39
Solutions
Badges
Apr 19 2022
12:11 AM
Recommend to check your firewall, Camera settings and to verify all switches/uplinks which are involved know this vlan (maybe it is new?)
... View more
Apr 19 2022
12:08 AM
5 Kudos
I would also recommend a 1Gb SFP module as well. And would add to be aware, this is not a Meraki SFP you are using. Maybe this can cause these crc errors as well.
... View more
Apr 18 2022
11:57 PM
We use 4 SSIDs everywhere... And on some APs even 5 SSIDs. So far, no problems. And got a good amount of devices within the locations/networks.
... View more
Apr 14 2022
5:18 AM
Haven´t done this yet, so I´m not sure. Would imagine it may interrupt for a short period of time, but someone else can probably give you more verified information. Do you maybe have a testlab where you can figure this out? BTW, understood it like you want to bind it to the old template again, which seem to cause in a problem.
... View more
Apr 14 2022
3:38 AM
1 Kudo
You may face a problem: https://documentation.meraki.com/General_Administration/Templates_and_Config_Sync/Managing_Multiple_Networks_with_Configuration_Templates
... View more
Apr 14 2022
3:27 AM
Isn´t this a restriction you make on your exchange? From where it is possible?
... View more
Apr 13 2022
11:42 PM
sounds like an IP address from another region / location was taken? That would of course explain why it didn't work. Since the subnet was not known. Then, as mentioned, the device makes a fallback to the old - working - address. However, great it got solved.
... View more
Apr 13 2022
11:24 PM
Does something need to be forwarded on your L3 switch? Any firewall in between, you forgot? Any multicast/IGMP snooping settings missing?
... View more
Apr 13 2022
1:04 AM
1 Kudo
This post is regarding to AirPrint, but could be a good hint: IGMP snooping - https://www.reddit.com/r/meraki/comments/icx2sz/bonjour_forwarding_and_airprint_printer/ And in addition to the reddit threat, this link is mentioned in the discussion: https://community.meraki.com/t5/Switching/Multicast-Basic-s/td-p/25706
... View more
Apr 12 2022
11:48 PM
2 Kudos
It is the same with MR-74, tested it (need to use them temporary indoor, firstly I just put it on a table) vertically is much better than horizontally, I can confirm this. surely it is regarding to the MA-ANT-20 design.
... View more
Apr 12 2022
11:19 AM
5 Kudos
Yeah, thanks a lot for this contest 🙂 Congratulations to all, specially to rbnielsen
... View more
Apr 12 2022
5:30 AM
Have you check if the IP you chose for the switch as future static IP is not already in use? Have you veryfied the new static IP is allowed to reach the internet on the necessary ports?
... View more
Apr 12 2022
5:25 AM
I do not understand this: "You cannot route traffic from other networks through a single network's tunnel in a 3rd party VPN" If you have Org A and Org B and all or all necessary subnets in this VPN-Tunnel, the systems build all IPSec-SA´s on their own. no one needs to set up seperated IPSec Tunnels for each remote network. Which I think is not possible to do several Tunnels between the same public IPs
... View more
Apr 12 2022
2:35 AM
2 Kudos
Need to add/ correct @Brash (sorry), WLC must not be directly in this network. You can forward the Cisco APs packets over VPN to the WLC. "IP helper address" are the keywords 😉
... View more
Apr 12 2022
1:52 AM
1 Kudo
You have two Orgs connected with VPN to each other and want to use resources like DNS from Org A in org B, correct? If you used Site-toSite-VPN you configure the remote site subnets and there has to be the subnets which are necessary. Afterwards the DNS server is reachable from the remote site. Keep in mind you may have to allow this communication in a third party firewall if you have one.
... View more
Apr 11 2022
11:59 PM
1 Kudo
We have these switches, too. Another argument: 10GBit Uplinks are used to connect to the coreswitches, in an AGGR to get 20GBit Uplink to cores and of course redundance.
... View more
Apr 11 2022
11:20 PM
You can connect them, and use PoE if you have it at your Switch, sure. But you will still need a WLC from Cisco classic to configure it.
... View more
Apr 11 2022
8:06 AM
Great idea... "Made a wish"
... View more
Apr 11 2022
8:03 AM
Get all configurations through API and rebuild it with these API calls. That is what should work. But if you are not into API - like me - it may be faster doing it manually... But would help for the future 😉
... View more
Apr 11 2022
7:53 AM
Looks correctly. restart done, ok This IP range is completely new on this site and the settings on the other end of the switche´s Uplink are correct as well? I would recomment to wait till tomorrow.v Maybe to restart it again. Very sorry to write this down, but this is the only way it worked for me in the past. And this was suitable for me, as I was not in a hurry. Edit: you can make the local status page accessable from "outsite" - Network-wide - general Maybe you can see something on the status page. Or try to configure it there. Hopefully this won´t make it worse 😉
... View more
Apr 11 2022
5:39 AM
ok, great. Do you want to share the IP settings once again, but only with blured public IP? Did you restart the switch - from dashboard (Switch - tools - restart)?
... View more
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 2863 | Apr 29 2022 5:15 AM | |
| 1766 | Apr 27 2022 6:29 AM | |
| 1616 | Apr 22 2022 2:56 AM | |
| 1658 | Apr 13 2022 11:24 PM | |
| 1639 | Apr 12 2022 11:48 PM | |
| 1516 | Apr 11 2022 8:03 AM | |
| 1614 | Apr 8 2022 4:49 AM | |
| 1449 | Apr 6 2022 5:10 AM | |
| 2936 | Mar 30 2022 6:23 AM | |
| 2353 | Mar 30 2022 4:10 AM |
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 6 | 1771 | |
| 6 | 16228 | |
| 5 | 1088 | |
| 5 | 4034 | |
| 5 | 5589 |
© 2024 Cisco Systems, Inc.
