Hi Nealgs, For the life of me I can't get the script to work. I have made sure everything is good and even tested my URL links outside of the script and can get to them, but I keep getting a blank readout when trying to display and when I try to run change I get a 404 error ... View more

I think you're trying to do VPN chaining. Not 100% sure it is supported by Meraki ... View more

Hi, Tehsin,    Were you able to identify the root cause of this issue I am having the same issue except I am using the local DHCP server service on the Meraki it self.   ... View more

Have a look at this link.  this is what we now use instead of splunk for our environment.   EventLog Analyzer - SIEM Log management software. (manageengine.com)   Runs on a single server, 12 core, 96GB RAM which also runs our Rapid7 scanning tools too. ... View more

not sure if this may be of help:   https://www.checkyourlogs.net/configuring-cisco-meraki-to-azure-site-to-site-vpn-tunnels-ikev2-azure-cisco-meraki/   I assume you have a public facing ip on the Win 2019 server that the Meraki can use as the endpoint for the Tunnel?     ... View more

we do it the same way as @PhilipDAth mentions.   We have a standard fibre BB connection from BT (we are in the UK) that we use to connect our test kit to meaning we can test them out before sending/deploying to site.   cheap solution 🙂     ... View more

Hi jay_b,   if you've used postman before, then stick with it for testing of the relevant calls and parameters they use.   with regards to powershell, i wrote the one posted in the link below and just used google and postman to help me.   postman for how the calls etc are formatted and what json results are returned and then google on how to create functions and subroutines,parse json data, use arrays etc in powershell.   rgds Gary (nealgs) ... View more

I just ran into this today on two new machines. I was seeing a 403 Forbidden error in Console when OS X was trying to request the provisioning profile during installation; then I'd get an ErrorCode:1 in the UI. I tried requesting the URL that appeared in the logs and ended up getting the log-in page for the self-service portal.   On a whim, I tried enabling authentication for enrollment (which, oddly enough, defaults to disabled on a fresh SM setup). You can find the setting under Systems Manager -> Configure -> General ("/manage/configure/system_settings") in your dashboard. After I did that, I tried downloading the enrollment profile again, got prompted for Meraki dashboard credentials, provided them, and then the profile that I downloaded installed fine.   Before trying the new MDM profile file, I tried the one I had downloaded from before I enabled authentication and it failed, but the one I downloaded after authenticating succeeded. I'm wondering if maybe SM has a bug where if you do not have authentication enabled when you download the MDM profile, it fails to authenticate properly. Perhaps the profile has a stale set of authentication credentials (resulting in the 403) but if you download one after authenticating it has refreshed credentials? Or something like that. Just conjecture; all I know is that things worked when I enabled authentication for enrollment. ... View more

Hi PhilipDAth   Your cookbook and online configurator is indeed a good tool and nice programming ... View more

What about monitoring with statuspage.io for example? ... View more

> Lastly, do I need to have Cisco Meraki support turn off the lower encryption (3DES?) that is being used for the VPN client currently, to pass the PCI scans?   They can't.  They can only specify one setting. ... View more

@wwWe've updated everything to the latest firmware and luckily never faced the issue again since then. But however, I've found nothing related to this issue in the any release note... ... View more

@nealgs Yes you may need to create a new EMM newtwork and then combine it with an exisiting network if you want everything in a single network.  ... View more

as a further update to this i tried again a bit later with IE to the same PC that earlier had worked and it didn't work 😞   oh well.... 🙂 ... View more

what was the issue NSM?   Might be worth adding it here incase someone else has the same problem further down the line 🙂   Glad you sorted it though    rgds Gary ... View more

Last night the rest of the MR18 were rolled-back. and I am already seeing major advantages with these access points on the older firmware. The connection log is showing a success rate of 79.9 %. of logging in. I push the Logs back over the last month and that connection rate drops down to success rate of 16.5%. I know the rate will only get better after I get an email together to send it out to the users with the Passwords for each SSID and department. I think that is some of my issues with the fail rate that I am seeing now.   Thank you for all the help and to have me reach out to support. Support has been amazing. I also hope this helps other with this issue, I know people are having it. I see the boards and no one ever has a solution, that is why I wanted to keep everyone up to date on what I found out. Wish everyone luck with this issue.   ... View more

We had a similar dilemma a couple of years or so ago when we began our migration to Meraki kit (so glad we did)   11 sites through-out europe ranging in size from 100 people to around 5 - plus host system at a data centre.   ended up with 2 MX84's for sites with 70 + users and rest went with MX64 and one Mx65 for site that was going to have dual circuits (but didn't in the end - doh! )   It's best to go have to much than not enough as you end up buying twice otherwise.         ... View more

Hey Everyone,   Just wanted to confirm what Gary has posted as the solution on this thread.   If anyone has any lingering issues, please check in with your ISPs and/or reach out to Meraki Support.   If anyone has any specific questions for myself please don't hesitate to send me a DM.     Rodrigo Meraki Support  ... View more

It was just two weeks ago, that my first Meraki system was installed.  I only have a very rudimentary knowledge of how to use my Meraki system and was nervous about getting all my Linn Music Streamers working; but with the help of those mentioned, we got it going.   Thanks for the recognition and kind words. 😊 ... View more

Just one other thought - make sure your Meraki APs can reach the Internet  (i.e. the Meraki cloud platform). You may need to open some access for this through your network and perimeter firewall;   check out Help > Firewall info, from the Meraki Dashboard, for the holes you need. ... View more

@CN this is so cool, thanks for sharing and thanks for introducing the idea to us in the first place 🙂   Here's the abstract to save you a click (though, of course, the rest of the paper is worth a perusal and they'll be updating with new info as it becomes available). So exciting to know we have been part of such an impactful project:   ... View more

On the dangers of IoT and fish front.   If you can, I'd put those cameras on a separate subnet with some firewall rules, in addition to patching the heck out of em. ... View more

It'll be a 100mbit connection.   1st and 2nd pair are data and are tested.  3rd pair is for poe and is tested.  4th pair ... specs says it can be used for poe so not sure.  I don't have a switch with a 100mbit PoE device that isn't affected by the 12.14 bug to test on 🙂 ... View more