Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About Shadius
Shadius
Building a reputation
Member since May 11, 2020
Community Record
146
Posts
32
Kudos
0
Solutions
Badges
Nov 11 2021
1:51 PM
@PhilipDAth So I'm seeing some PermitAccess and others show blank. I just ran the test from the Meraki Dashboard and I see the two access points that are alerting show the Identity as USERNAME and under the Authorization Profiles, it's blank. The access points that went through show my Identity as my username and show PermitAccess for the Authorization Profiles.
... View more
Nov 11 2021
12:39 PM
Hi all, I'm having issues with getting Cisco ISE to work with the Cisco Meraki Wireless Access Points. All the access points have been added into Cisco ISE. When testing connectivity to the wireless network a few weeks back, it all worked flawlessly. Now, I am prompted for a username and password and when I enter it, it doesn't connect. While connecting to the wireless network, it will just say "Can't connect to this network." I'm not sure what's going on. Nothing has changed. I have some access points able to communicate with Cisco ISE and some are alerting that it cannot connect. What can I check to begin troubleshooting?
... View more
Nov 11 2021
10:57 AM
I spoke with our System Administrators at our Data Center. We're using NIC Teaming, but it's configured through Dell's Broadcom Advanced Control Suite 4. Found this link: https://www.dell.com/support/kbdoc/en-us/000105133/how-to-set-up-nic-teaming-on-windows-server-using-broadcom-advanced-control-suite-4 All of our sites are configured this way. The decision to make would be whether it's better to set up LACP at all of our sites. I'm not sure if there's a pros and cons of using Dell's Broadcom Advanced Control Suite 4.
... View more
Nov 8 2021
6:20 AM
Thanks@PhilipDAth Is there a best practice for setting this up? I believe we are using NIC Teaming.
... View more
Nov 6 2021
4:49 AM
Hi @ww Correct. Currently LACP is not configured. I'm not too familiar with LACP, so bare with me. No ports are aggregated on the switches from what I can see. Yes, the DC is connected to our MS350 switch and each switch port is configured as an access port. We have a three switch switch stack and the connections are split between Switch 2 and Switch 3. I will have to check with our System Administrators about the mode of NIC Teaming, but it might be set to Switch Independent.
... View more
Nov 6 2021
3:26 AM
Love rocking the Meraki gear!
... View more
Nov 6 2021
3:21 AM
Hi all, I am receiving IP conflict alerts from the MX250 about our Domain Controller using NIC Teaming. It seems like the NIC ports are taking turns coming online. One port loses connection, the other comes online. Is there any explanation of why this may be happening and how it can be resolved?
... View more
Oct 29 2021
3:48 PM
Hey all, Is there a way to change the password of all the SSIDs I have altogether? I have multiple sites with multiple Cisco Meraki wireless access points. When it's time to change the password for each SSID, I don't want to have to go into each individual site's SSID and manually change the password every time. Thanks in advance.
... View more
Labels:
- Labels:
-
SSID
Oct 29 2021
3:42 PM
Yes, I did notice this function when I upgraded the firmware for the switches. Thank you for the explanation and suggestion @WirelesslyWired It seems that cycling the port has stopped the alerts also. Thank you @EJN
... View more
Oct 25 2021
10:33 PM
Hi all, I've recently started receiving alerts of IP sharing after a power outage. It goes on to say "NAT has been detected on 1 client in the...," etc. I'm not sure what it means exactly. Prior to the abrupt power outage, I've never received these alerts before. Can someone educate me, please? Thanks in advance.
... View more
Oct 23 2021
2:23 PM
@DarrenOC The trace route shows it timing out on the 4th hop. After inputting a static route on the WAN router for it to go to the Cradlepoint E3000 Router (172.16.150.9), the trace route shows it starts at the interface IP (172.16.150.11), then goes to the Cradlepoint E3000 Router's IP, but times out from the 4th hop to the 8th hop, then resumes on the 9th hop. When removing the static route of 172.16.150.9, there is no timeout, but computers get 1Mbps speeds, which is our WAN circuit speeds. Also, a speed test ran from the Cradlepoint's NetCloud Manager resulted in over 100Mbps speeds. Here's a screenshot:
... View more
Oct 23 2021
2:55 AM
The Cradlepoint E3000 Router is connected to the Cisco Meraki MS350 switch port 1 as an uplink with an internal IP address. The same Cisco Meraki MS350 switch is connected to the Cisco WAN router. There is also another switch on a different floor that is connected to this switch using a trunk port. Yes, we do have L3 VLAN interfaces on each switch.
... View more
Oct 22 2021
1:45 AM
Hi all, We've connected a Cradlepoint E3000 Router to our Cisco Meraki switch and set the static route to go to the Cradlepoint's IP address which is on our network, however, we don't seem to be getting speeds from the Cradlepoint. The Cradlepoint speed test would show anywhere above 100Mbps, but yet the computers get 1Mbps. We want to use the Cradlepoint for our Internet. What can I check to start troubleshooting?
... View more
Oct 12 2021
12:14 AM
We are trying to decide whether we should put the printers on their on subnet or VLAN. I'm not sure what the best practice is for this scenario. I guess I could just add firewall rules for each printer's IP address. The printers all have static IP addresses.
... View more
Oct 9 2021
7:41 PM
According to this article, I can set my "guest" network to NAT mode: Use Meraki DHCP to have the guests on a 10.0.0.0/8 network and still permit them access to the wired LAN network if the SSID firewall settings permit. However, if I allow access to the Local LAN through the SSID firewall settings, will this only apply to the printers on the Local LAN or everything in the Local LAN?
... View more
Oct 9 2021
6:22 PM
Hi all, I'd like to create an SSID for guests to access the Internet and also be able to only have accces to our organization's printers. Is there a way to do this while restricting access to the rest of our network resources?
... View more
Jun 25 2021
12:58 PM
So I'm not getting any link light when I plug into the Management interface at the back of this switch. The switch is assigned a static IP and I'v confirmed it's set correctly. Even though I'm not getting any link lights from the management interface, I still tried to access switch.meraki.com and was taken to the local status page of another switch that's on a different switch stack and floor.
... View more
Jun 24 2021
10:08 PM
When removing the switch as a member of the switch stack, will it remove the configuration on the switch as well?
... View more
Jun 24 2021
9:52 PM
Hi all, I am having an issue with a switch stack of four MS350-48FP switches. My Dashboard is displaying the following: "This switch's current stack members differ from the dashboard configuration." The third switch in the switch stack is stuck on an orange LED status light. I've tried to reboot the entire switch stack, but nothing has changed. How can I troubleshoot this to resolve it?
... View more
Jun 17 2021
12:41 PM
@BrandonS The map would show the address, but I've never gotten the chance to use the floor plans feature in the Meraki Dashboard since our organization has a hard time of obtaining them. However, in a case where there are multiple IDFs on the same floor, I'm trying to come up with a short and sweet naming convention. For example, the 2nd floor has IDF 1 and IDF 2 with each IDF having their own switch stacks. In the future, we're planning on consolidating our offices and doing a floor plan layout to move the MDF and IDFs. Thought I'd get a head start.
... View more
Jun 17 2021
12:36 PM
@DarrenOC Pretty similar to ours except without the Country Code. I imagine your company is country wide.
... View more
Jun 17 2021
12:13 PM
2 Kudos
Hi all, I'm curious to know what naming conventions do you use for your switches? My company likes to use the following format: Site Address - Number of Floor - Switch Number This naming convention can get long due to the address, so I am looking into formats that will shorten the length while still looking neat and giving the correct information. We have multiple switch stacks in buildings with a lot of floors.
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 4 | 1236 | |
| 4 | 19047 | |
| 4 | 5750 | |
| 3 | 14180 | |
| 3 | 1348 |
© 2024 Cisco Systems, Inc.
