Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About Thygesen
Community Record
137
Posts
84
Kudos
3
Solutions
Badges
Mar 4 2020
2:32 AM
1 Kudo
@MeredithWAnytime 😀 I'll hang in there and spread the word among my peers.. /Thyge
... View more
We discovered that it was only the MR70's (running 26.0 software) that had the issue.. All MR's are now at 26.6.1 and no noice in the logs .. 😀 Remaining "noicers" are only workstations as others see in this forum ..
... View more
Feb 25 2020
12:56 AM
So I'm not the only one .. Thanx @MichelRueger Any news from Meraki... ?? Anyone ??
... View more
Agree.. Seems "workstations" only ..
... View more
Hi @Matttt -.- We still see lots of these .. And we also tried the new switch sw, but reverted, since it did no good in the matter. It seems that uplinks/trunks and workstation links are affected and not selective 😉 All switch-types are affected. It bursts 10-15 entries in the log in each occurance.
... View more
Feb 13 2020
2:40 AM
Hi @jwwork ! I see similar behaviour on a couple of switches running MS 11.30..
... View more
Feb 5 2020
12:54 AM
Excellent idea with the lab .. I always do/recommend this in larger environment (pre-prod setup). I don't have the MR32, so I did not get any indications of instability .. Worrying indeed, could You post your responses from the Support case, when things turn brigther ? In any case: Good luck tracking down the issue .. With highest regards Thyge
... View more
Worx like a charm .. Upgraded smoothly and no trouble at all so far .. With highest regards Thyge
... View more
Feb 3 2020
2:28 AM
2 Kudos
Maybe it's the new telekinetic interface at the portal ? "Your MX has now been moved .. " 🙂 Nah .. sorry, bad joke .. Hope it all clears up .. /Thyge
... View more
Feb 3 2020
1:10 AM
😉 We did that already 🙂 Just curious as to what might happen .. /Thyge
... View more
Feb 3 2020
1:09 AM
1 Kudo
😞 Sorry to hear that .. All mine looks normal now .. give'm a call at support .. maybe it is something else ? With highest regards Thyge
... View more
Jan 31 2020
4:12 AM
1 Kudo
@BrandonS @CarolineS So .. How are thing rolling along with Partner specific boards ? Long time no news ? With Highest Regards Thyge
... View more
Jan 31 2020
12:20 AM
2 Kudos
Well .. That seemed to get things moving ? The funny look is now gone this morning .. 😀🕺🎉 It will be interesting to see what the answer will be in the case .. / Update: From the Meraki Support team : I have received confirmation from development that yes the issue has been resolved. It was a backend dashboard error. / End of Update
... View more
Jan 29 2020
1:14 AM
@AustinCWhoops .. 🙄 I'll log a case immediately. Just posted here, and got a reply that would get back, chasing the case. I still think the info should be streamed here as well as in a closed forum as in the Meraki Support.
... View more
Hi @redsector .. I only have AP's connected to the ports doing this .. No issues on uplink ports as well as You observe .. Will be interesting to hear what the Engineers say ?
... View more
I will listen in on this .. We see these A LOT!! (like a zillion times a day) and I should be much mistaken if all the cables/plugs were faulty everywhere in the installation .. Any news ? (SW: MS 11.30)
... View more
Jan 28 2020
2:23 AM
I'm with You there @Twitch .. As I read it, the ECMS2 is last part if a set of education courses with tests and all .,. I too would like to finish what I start, and have not seen one single announcement for this Course. As to the education team is limited and only can do so much, it somewhat collides with the facts from this thread with "multi-million$ installations" and all .. I would also like to hear some official viewpoints from Meraki on this .. With highest regards Thyge
... View more
Jan 27 2020
3:21 AM
@cmrSo .. how did it go ?
... View more
Jan 21 2020
12:19 AM
Thanx cmr .. It does not look nice when demoing the Topology .. With highest regards Thyge
... View more
Jan 20 2020
11:57 PM
1 Kudo
Regarding my image (with the ports) 😉Yep, got it .. It was just to show that the network actually had a MX device 🙂 I found the reason (marked very green in the thread) thanx to You all .. I'm humbled 😉 With highest regards Thyge
... View more
Jan 20 2020
11:37 PM
1 Kudo
Thanx a LOT, jdsilva! That did it! How great, that You are awake, and can guide a rookie like me ! I whish I could give more than one Kudo, since the answer was swift, exact and illustrative, all at the same time .. Thanx 😀 from the high North (Denmark 😱) With highest regards Thyge
... View more
Jan 20 2020
11:35 PM
2 Kudos
I highly agree !! 2xKudo's from mee too! WOW That sure did the trick .. THANX a LOT !! With highest Regards Thyge
... View more
Jan 20 2020
11:33 PM
Hi .. Nice to hear that I'm not the only one .. Should we do a coordinated official report ? Or can we highlight this thread to engineering ? With highest regards Thyge
... View more
Jan 20 2020
5:48 AM
Hi .. The summary report is there, but there is not the graph mentioned .. The MX is also there, as You can see here: / Thyge
... View more
Jan 20 2020
4:52 AM
Hi All ! I'm looking for the graphs displayed in this link https://documentation.meraki.com/MX/Monitoring_and_Reporting/Device_Utilization They boast about the ability to see exiting stuff in the summary report .. I guess I haven't configured my report right, because I can't seem to locate the kind of graph they hint at .. Any suggestions ? With Highest Regards Thyge
... View more
- « Previous
- Next »
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 3091 | May 29 2020 5:12 AM | |
| 3157 | May 6 2020 11:27 PM | |
| 8842 | Jan 31 2020 12:20 AM |
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 8 | 1116 | |
| 5 | 43470 | |
| 4 | 169 | |
| 4 | 21202 | |
| 4 | 23571 |
© 2025 Cisco Systems, Inc.
