I see from the below image that they are the same ...  Thanks everyone. ... View more

Thanks 🙂 ... View more

But isent that image the MR42E ... is the portlayout the same on the 46E ? (me not knowing or remembering 🙂 ) ... View more

Yes ... But of the 6 ports ... what port is what ? I cant find any pictures online of this. I have had MR46E "in hand" before, but I cannot remember the "layout" so to speak.   ... View more

I also wonder what the "with all security features enabled" numbers will be 🙂 ... View more

Yep, I dont understand why the MX250 and MX450 has not been updated on the "Sizing guide", since all the new MXxx5 models have been updated previously this year. (this year .. DOH ... last year 🙂 )   But the numbers should roughly be : MX450 goes from 4 to 10Gbit (NAT EMIX)  - 1,5 to 4,5Gbit (VPN EMIX). MX250 goes from 4 to 8Gbit (NAT EMIX)  - 1 to 3Gbit (VPN EMIX) ... View more

New Unit. ... View more

Im just listening in here  🙂 - Just because of findings on the MR46E 🙂 (My "rants" about that can be found somewhere on these forums Im sure 🙂 ) ... View more

One request. Could you upload the pcap file here, just so I can have a look at it ? 🙂 ... View more

Yep I have also run the 916x APs in "DNA persona" in survey mode almost without issue (except being locked out from the UI for some strange reason). I just like the Meraki Survey mode, and it worked just as expected in the MR29 software. ... View more

Thanks, this 100% confirms my findings. No FILS or UPR on 6Ghz while in survey mode == you cant use it for surviving 6Ghz in MR30.x   And this also gives me a reason to why my Intel Laptop with the "lite" tool found the network on 6Ghz, it most likely got it from the 2,4 or 5Ghz beacon (as is allowed in the specs for 6Ghz , sometimes called "out-of-band discovery" or reduced neighbor reporting (RNR) (as far as I know). )   But bottom line is; when it does not send FILS or UPR in survey mode, you cant use it for surveying. Thanks for all your work, I think I'll just point support to this forum page 🙂   /Thomas   ... View more

Please do. Remember to set the flex-radio before putting it into survey mode to 6Ghz and, have it connected to the dashboard for more then 2 hours 🙂 I'll eagerly await the result 🙂 Thanks 🙂 ... View more

PS: I now also have a case open, and so far, I have been told that the 9164 / 62 cannot "do" survey mode on 6Ghz because it is not a "flex-radio" ... excuse me, what ? I think it was just the support person who misunderstood what the support page says about flex. : https://documentation.meraki.com/MR/Wi-Fi_Basics_and_Best_Practices/Conducting_Site_Surveys_with_MR_Access_Points If true, and it changed for some reason, because I have used 9164 for survey in the MR29 software, it should be in that document in large red letters or something 🙂   I did however notice that it now requires the AP to be online in the dashboard for at least 2 hours ( most likely to be sure of reg. domain ) before it will work. ... View more

Yeah, you can do " ap-type site-survey" as a command now on those 916x APs (from 17.something release) of 9800. - When I tried it, it worked just fine. But .... unfortunately, for some reason, i got locked out of the AP after logging into the UI the first time. The default, in DNA-Persona survey-mode, should be admin/admin, but for some reason it changed. I will try again at some point on a newer 17.x release.  ... View more

Well in survey-mode there is only one SSID. And it worked just fine in MR29 for those APs, so something has changed. And the "fun ting" is that the simple tool WiFi Explorer sees this SSID (on 6 GHz) in the first ... "5 minutes" after the AP has booted. Then it goes away. Unfortunately I have not gotten an Ipad with USB-C yet, so I cannot use the SK2 for a packet capture. I really want to see whats going on. ... View more

I think there is a bug in MR30 when in survey mode for 6Ghz. When switching to survey mode, I very briefly see the 6Ghz survey ssid from the AP when using a tool like WiFi Explorer Lite. But I NEVER see it using Ekahau SK2. My speculation is that the AP simply does not do FILS or Unsolicited probe response when in surveymode, and WiFi Exploere Lite only "found it" because the Intel NIC in my laptop did a passive scan. - This is bad, it has to do FILS or Unsolicited probe response in order for us to use it as a survey AP. (Im fairly certain it did in MR29 software, because I had a 9164 running in with that software for a long time in survey mode without issue). ... View more

Just for good measure ( measure, survey, pun intended ? 🙂 ), I created a case for "6Ghz not working in survey mode". I have yet to have any useful feedback on it. ... View more

This could work : https://documentation.meraki.com/MR/Encryption_and_Authentication/Meraki_Local_Authentication_-_MR_802.1X As long as you can speak "LDAP" with your Azure AD. ... View more

Being a positive person, Im sure it will happen at some point 🙂 - Just give it a little time 🙂 ... View more

I would recommend setting the channel-width to something static, instead of auto (from the picture though, all your APs are running the same channel-width , so no worries) - But, from experience, some clients prefer wider channels, so for example, if an AP is running 80 Mhz but far away, and a much closer AP is running 20, some clients will still prefer the wide (but far away) AP 😕   And while you are "playing" why not enable more 5Ghz channels, looks like you are only using the non-DFS ones (depending on reg-domain of course). If worried about DFS I recommend enabling the Auto RF / AI channel planning. That actually seems to be ok, when in a DFS environment (again only from personal experience).    Also , from experience, remember to disable "Client balancing", I think it's still enabled by default on Meraki RF profiles. To me "Client balancing" is very useful for high density, like lecture halls and so on, but for a normal office environment, I always disable it, because historically, it has only caused trouble. ... View more

I see that the documentation for this has been updated (Last updatedApr 13, 2023). Now it does not mention any special , ehhh, "conditions" for different models. Will it now work, across all switches regardless of port density ? - do anyone know ?   ... View more

Perfect this looks like the (for now, until the 9300X is introduced in an "-M" SKU) answer I was looking for. Thank you. ... View more