Has there been any further movement on route summarization from meraki   ... View more

Hi, the same thing happened to me with my AWS environment. We had to restart the machine to bring the tunnels back up. Is there any known solution to this problem? ... View more

Hi,   Is there a more up-to-date version of this? ... View more

These threads just solidified that I will work on a new solution for my sites since I am down to the last 3 months of my current licensing. I was considering switching over to Meraki, but I cannot take the risk that this could happen to any of them. I will try the Onada solution and see where that takes me. Thanks all for the info. ... View more

I had to open a case with Meraki TAC.   The only thing they told me was that it was a known issue.   But they still didn't know which version it would be resolved in.   So they made an adjustment in the backend but they never told me what it was.   Since that moment the problem has not occurred again. ... View more

I wrote this using the Meraki PowerShell Module. It doesn't reset them 100% but it is very close.  Note: This will reset all SSIDs for the entire organization use with caution. PowerShell Module  # Reset All SSID to Unconfigured v1.9 Import-Module Meraki $AuthToken = "xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx" $OrganizationID = "xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx" $SiteNames = Get-MerakiOrganizationDevices -AuthToken $AuthToken -OrganizationID $OrganizationID | Where-Object {$_.Model -like "*MX*"} | Select-Object Name,NetworkID $SiteNumber = 0 ForEach ($NetworkID in $SiteNames.NetworkID) { $SiteNumber = $SiteNumber + 1 Write-Host $SiteNames.Name[$SiteNumber] ForEach($Count in 0..14){ $SSIDName = "Unconfigured SSID "+$Count $SSIDConfig = [PSCustomObject]@{ name=$SSIDName enabled="true" authMode="Open" ipAssignmentMode="NAT mode" mandatoryDhcpEnabled="False" splashPage="none" perClientBandwidthLimitUp="0" perClientBandwidthLimitDown="0" perSsidBandwidthLimitUp="0" perSsidBandwidthLimitDown="0" } $SSIDConfig = $SSIDConfig | ConvertTo-Json -Compress Set-MerakiNetworkWirelessSSID -AuthToken $AuthToken -NetworkId $NetworkId -SSIDNumber $Count -SSIDConfig $SSIDConfig $trafficShapingRules = [PSCustomObject]@{ trafficShapingEnabled=$false defaultRulesEnabled=$false } $trafficShapingRules = $trafficShapingRules | ConvertTo-Json -Compress Set-MerakiNetworkWirelessSsidTrafficShapingRules -AuthToken $AuthToken -NetworkId $NetworkId -SSIDNumber $Count -trafficShapingRules $trafficShapingRules $L3FirewallRules = [PSCustomObject]@{ allowLanAccess = "true" } $L3FirewallRules = $L3FirewallRules | ConvertTo-Json -Compress Set-MerakiNetworkWirelessSSIDFirewallL3FirewallRules -AuthToken $AuthToken -NetworkId $NetworkId -SSIDNumber $Count -L3FirewallRule $L3FirewallRules } ForEach($Count in 0..14){ $SSIDName = "Unconfigured SSID "+$Count $SSIDConfig = [PSCustomObject]@{ enabled="false" } $SSIDConfig = $SSIDConfig | ConvertTo-Json -Compress Set-MerakiNetworkWirelessSSID -AuthToken $AuthToken -NetworkId $NetworkId -SSIDNumber $Count -SSIDConfig $SSIDConfig } }     ... View more

No Uptime in our MSP dashboard.   And we have a situation past few days for a client that is going offline every 2 hours.  Would be nice to confirm if it is indeed infrastructure power or ISP related. ... View more

Hooray! We have some new Visio shapes! These were a side project of a Meraki employee, @DrDray - so they're not in the official Visio .zip file on cisco.com but.... take a look! https://community.meraki.com/t5/Dashboard-Administration/Meraki-SVGs-Visio-LucidChart-Stencils/m-p/215661 ... View more

I have the Lift-off badge, guess you got to start somewhere.  Looking to earn more in the future. ... View more

What about when there is no internal DNS?  What about if it is a non-Windows environment?  What about devices that can't register in internal DNS (printers, cameras, scanners, etc)? ... View more

Hi @Khaled_A You need to configure a local DNS-Server(Raspberry Pi or any device) on the same network where you need the local hostnames. Then connect the lan port of this DNS server to one of your switches and ping the IP and hostname of the server from your router to see if everything works properly.   Then you can create the desired local DNS names via an A record on your local DNS server and point the local DNS names to your local IP address that you want to reach with hostnames. So that's it! ... View more

you are right Sarv. I did also proceed like this, except not configuring LAG and just letting SPT makes the job to shutdown one port. it works then as a simple official network link for VLANs. ... View more

@Inderdeep: for the setup you have made, which I believe is the non-meraki site2site vpn, all ipsec details will be coming from the Viptela side and that would limit the IPs that the Meraki can learned from the Viptela routes. Will you be able to share the setup or diagram? ... View more

The real question is. What "chip" does the RF analysis on the new 916x APs. They all have the CleanAIR Pro "chip/board" inside of them, because of the common hardware. But is Air Marshal and / or RF Spectrum using this chip ? or just the client facing normal Wifi chip ?   ... View more

Another option: Buy web filters separetly (Barracuda, BlueCoat, etc.) Buy Firewalls without subscription (Cisco, Fortigate) or free pfSense / OPNSence Buy SD-WAN from Fortigate or Palo, since MX doesn't do SD-WAN at all:) Pay your admins / engineers more to addminister all this stuff😀 ... View more

I am seeing utilization as follows. Select the desired Network at the top. Highlight Organization and then Summary Report under the Monitor menu Change Network(s) from "Entire organization" to "A single network" Select the appliance of your choice It displays below the graph on the lefthand side ... View more

This feature is called the "Enhanced WAN failover and failback". Only enabled via Meraki support. ... View more

Wondering if this was ever resolved? ... View more

WPA3,  https://documentation.meraki.com/MR/WiFi_Basics_and_Best_Practices/WPA3_Encryption_and_Configuration_Guide   in MR 27.x And IPv6, https://documentation.meraki.com/?title=MX/Networks_and_Routing/IPv6_Support_on_MX_Security_%26_SD-WAN_Platforms_-_WAN and in MR 28.x ... View more

I know this is a very old post, but I am experiencing the same or similar with an Ubuntu Server.  The Meraki alert is attributing the MAC address from each of the two NICs to the same single IP address we have assigned in the DHCP server to just one of the NICs. I know this has something to do with "teaming" as we attempted to team the NICs on this system, but did not ever get it to complete fully.   I suppose the alerts are evidence that some sort of teaming may be occurring since its detecting the MAC address change and alerting us.  I don't really have a solution yet, but this post has pointed me in the right direction. Thanks.   ... View more

Is WEP still the encryption for mesh networking between the APs? ... View more

Agreed.  We currently are using the dual MX setup. It’s not ideal. Certainly the MXx5 line has the processing power and already have 4 dedicated WAN ports. (2 get greyed out). Is there any update on when and if Meraki will update firmware to activate more than 2 at one time?  Pipedream?  Or at the least allow a failover when one of the 2 actives goes down. ... View more

Congratulations! Let me get on yall's level!! #merakimagic ... View more

No, this is about setting the time zone, not turning automatic time zones on/off. ... View more