Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About PJB
Community Record
19
Posts
0
Kudos
0
Solutions
Badges
Feb 16 2024
12:33 AM
Ok many thanks. Setting up Site to Site VPN is easy enough to a non Meraki Device?
... View more
Feb 15 2024
3:59 PM
I am trying to ping from outside my network. Ping is allowed and there i no FW on the Pi
... View more
Feb 15 2024
12:01 PM
Hi no I dont see any rules blocking, very simple set up;
... View more
Feb 15 2024
9:32 AM
Hi all, I have a Raspberry Pi connected to a MS switch in its own Vlan and for the some reason I cannot connect or even ping the device remotely. I have set up 1to 1 Nat from my Public IP but still no joy. Any help much appreciated
... View more
Dec 17 2023
4:57 AM
Hi there, Many thanks for that script. I am not familiar with implementing them at all and quite noobie regarding API configuration etc. Is this the only other way this can be done? Can you walk me through it
... View more
Dec 14 2023
12:04 AM
Hi there, I am looking for a solution to this issue; I have set up a Corporate SSID for new remote users. They gain access via a PSK only (No radius involved etc). However, how do I set up a prompt/alert that the password needs changing after 90 days. Even an email to send to the support desk so that they can inform the users of a new password. All help much appreciated
... View more
Labels:
- Labels:
-
Other
Oct 11 2023
4:44 AM
Hi there, Yes both printer and device are receiving IP. I can ping them both from Meraki dashboard from all vlans.
... View more
Oct 11 2023
12:47 AM
Still having the issue. Also from the dashboard I can ping the printer from all other SSID's Vlans I set up, which I dont want, especially the test guest SSID. I have attached all relevant information. Hope you can shed some light on this.
... View more
Oct 6 2023
9:59 AM
Hi there, Many thanks for your reply. I can see L2Lan isolation is not enabled (Which is correct?) and no deny rule in place. Any other suggestions much appreciated
... View more
Oct 6 2023
7:35 AM
Hi there, I have created a test network. Essentially, 1 SSID (10.10.10.0/24) I have only a laptop and a printer connected via the AP. So Wirelessly connected to the same SSID and I cannot print anything. I have tried pinging the printer from laptop and no joy. I have all relevant drivers connected etc. I used my phone as a hotspot and connected both and all worked as expected. Any help much appreciated. My full kit is..Meraki MX to Switch to AP. Nothing crazy just 1 vlan created for the Test SSID and trunked all the way from MX to AP. Any help much appreciated
... View more
Jun 7 2023
3:43 AM
Hi there, Can an AP just be connected to broadband directly..SO essentially just plugging in APs directly into the hub that the ISP provided? Will these directly connect then to the ashboard? Also, can the ip/subnet ranges then be configured on the dashboard for these AP's. Basically, Ive no MX or Switches and want to configure the APs SSID's and there networks. ANy help much appreciated..bit of a noob here
... View more
May 16 2023
5:22 AM
Hi there, I am looking to set up MX75, MS210 and a couple of CW9162I AP's. This is a Proof of Concept. I have a question; can i set this all up at home then go to site and essentially plug and play? Will it have an issue if devices being registered on the dashboard and seeing my home Public IP address and then when moved to the PoC site it will not work because of different Public Ip address? Any feedback welcome
... View more
© 2025 Cisco Systems, Inc.
