Alerts MS390 upgrades to this version will experience a full system reload Branch additions Syslog support for MS390 series switches SNMP support for MS390s RADIUS accounting support for MS390s Alternate Management Interface support for MS210/MS225/MS250/MS350/MS355/MS410/MS425/MS450 series switches QoS support for MS390s CoA support for MS390s STP anomaly detection events for non-MS390 series switches Adaptive policy support for MS390 series switches SecureConnect support for MS210/MS225/MS250/MS350/MS355/MS410/MS425/MS450 series switches Bug fixes L3 stack stability improvements In very rare circumstances, MS220/320/420 series switches would encounter boot loops In rare instances, redundant links on stacks can incorrectly stay in a forwarding state if a stack member is rebooted In rare circumstances, the next hop VLAN is incorrectly modified for existing OSPF SVIs when a new SVI is added which will also participate in OSPF. A reboot will correct this (present since MS 11) A high amount of constant STP TCNs in a network may result in instability, and in rare instances, switch crashes Default SGTs are missing from the Adaptive Policy configuration Deconfiguring Adaptive Policy could result in the switch going offline IPv6 router advertisements sent by unicast to the link-local address are missed In rare instances, when a stack reboots, ports may come up as "LACP blocked state", even if LACP is not configured (present since MS 10) In rare instances, non-MS390 switches will reboot (present since MS 12) Known issues In large layer 2 networks, MS390s may drop ARP packets if there is an excess of 500 ARP packets per second In rare instances, a switch stack member may reboot MS390 ports are limited to the lowest link speed since boot if QoS is enabled In rare instances, non-MS390 switches will reboot (present since MS 12) MS120s may show PoE usage on the incorrect port In rare instances, a stack member may go offline until rebooted (present since MS 12) In rare instances, non-390 stack members will reboot (present since 12.29+) Packet loss is observed when pinging the MS390 management IP MS120s on rare occasions will reboot (present since MS 11) Stackpower is not enabled on MS390s by default Broadcast types of traffic can leak into the Guest VLAN if a port that fails authentication has a Voice VLAN configured, and dashboard has a Guest VLAN defined (present since MS 11) Links being established on a MS120 can result in neighboring ports to flap (present since MS 11) MS120s with multiple access policies enabled may reboot when port changes are made MS390 - Port Up/Down Events Shown Across All Members Clients connected to a trunk port on the native VLAN will show "native" for the VLAN information rather than the native VLAN ID. Enabling Combined Power on MS350/355 switches results in events being logged once per minute (present since MS 11) Networks containing a large number of switches may encounter issues saving changes on the Switch Settings page Stack members are not being marked to update their configuration when changes are made on other members mGig switches will have an amber light for all physical ports that do not negotiate to the highest supported speed. Dashboard will continue showing a light green status for all ports above 100Mbps. Example, MS355 switchports will incorrectly show an amber light for 1G, 2.5G, and 5G, but will show a green light for 10G. The list of switches to clone from fails to load when cloning a switch in an organization with a large number of switches and networks MS120s switchports with MAB authentication may randomly deauthenticate clients. In order to resume client authentication on that port, a switch reboot is required (present since MS 12) MS390 stacks on rare occasions will require a manual reboot after the upgrade has completed MS390 series switches do not support SM sentry MS390 series switches do not support Meraki authentication MS390 series switches do not support URL redirection MS390 series switches do not support MAC whitelists MS390 series switches do not support loop detection MS390 series switches do not support warm spare/VRRP MS390 series switches do not support UDLD MS390 series switches do not support MAC flap detection MS350-24X and MS355 series switches do not negotiate UPoE over LLDP correctly (predates MS 10) Rebooting any MS390 stack member via the UI will result in the entire stack rebooting
... View more