About Brash

Brash · ‎12-15-2022

I FOUND THE GNOMES! A new beta appliance firmware is now available on Thu, 08 Dec 2022 - The Meraki Community

Brash · ‎12-15-2022

Yes the MX would relay DHCP to the DC's

Brash · ‎12-14-2022

Version 16 firmware saw some significant performance improvements. Some people have noted issues on v17 (although none bandwidth related that I've seen). Other than checking the usual - disabling security settings, ensuring no traffic shaping etc - it might be worth testing downgrading back to the latest 16.x or opening a case with support.

Brash · ‎12-14-2022

Utilizing the existing equipment, you would create the new VLAN's with L3 gateway's on the MX100 (under addressing & vlans in the dashboard), then trunk the VLANs down to the switches and AP's.

Brash · ‎12-13-2022

The following link describes what happens for each different product line. https://documentation.meraki.com/General_Administration/Cross-Platform_Content/Behavior_during_Connection_Loss_to_Cisco_Meraki_Cloud#MS If the config is safe (see link for further detail), then it will continue to run until next reboot.

Brash · ‎12-12-2022

Love it! Although 11am ET is a bit too early for me. 😞

Brash · ‎12-12-2022

At this point I would start taking some packet captures along the path to track where the DHCP discover gets to.

Brash · ‎12-12-2022

What is the native vlan set on the trunk port connecting to the AP? Do you have any firewall rules set on the SSID? Do you have DHCP guard set on the SSID?

Brash · ‎12-09-2022

Well done everyone! Great and meaningful work! 🙂

Brash · ‎12-08-2022

Yes, you can use a flow preference for this. However, you cannot use FQDN's for the destination. It needs to be either an IP or subnet in CIDR notation. Also, in your example, the source port is unlikely to be 25. It will most likely be an ephemeral port number and therefore you're better off leaving it as Any. More info at link below. https://documentation.meraki.com/MX/Firewall_and_Traffic_Shaping/MX_Load_Balancing_and_Flow_Preferences#Flow_Preferences

Brash · ‎12-07-2022

Use Network Default means that it will use the settings configured in the VLAN, SSID or security appliance policies rather than overriding them.

Brash · ‎12-07-2022

It looks like the webpage is either doing a redirect or loading an iframe which is blocked - itfbodn.com

Brash · ‎12-07-2022

Can you provide some more information (and/or screenshots) about the URL, what you've placed in the URL allow list, and the block page that you're seeing?

Brash · ‎12-07-2022

I believe the AP reports the SNR value from between the AP and the client (so from the AP's perspective)

Brash · ‎12-07-2022

"Over the next month, we will be evaluating your contributions to determine the 2021 cohort of All-Stars" I didn't realise my contributions would be backdated to 2021! 😛 Jokes aside, exciting news. 🙂

Brash · ‎12-07-2022

Congratulations everyone

Brash · ‎12-07-2022

Channel utilization is an indicator or interference and is unrelated to the number of associated users. In your scenario, your AP is broadcasting on channel 6 and is indicating that there are other devices within range broadcasting at that same frequency, thereby causing interference.

Brash · ‎12-07-2022

Meraki brought in a requirement for all accounts to also require an OTP. Where MFA isn't setup this is on the form of an email. There is no way to disable this security feature. Further info at the below link https://documentation.meraki.com/General_Administration/Other_Topics/Authentication_Enhancements_and_New_Dashboard_Security_Features

Brash · ‎12-06-2022

Getting over 1Gbps throughput with stateful inspection is an expensive endeavour in comparison to free kit. That said, if you're willing to spend, the sizing guide below will show you the different models and applicable specs. https://meraki.cisco.com/product-collateral/mx-sizing-guide

Brash · ‎12-05-2022

What shard are you on? I'm not seeing any issues on shard 280.

Brash · ‎12-05-2022

How does the solution work? Where does it send the WoL packet from?

Brash · ‎12-05-2022

When a group policy is applied to a vlan, it is assigned to all clients within that vlan. So in a packet from host 1 to host 2 (in two different vlans and with group policies applied to those vlans), host 1's group policy is taken into consideration. Then the reverse for the reply packet.

Brash · ‎12-04-2022

Have never received an email like that. What address is the email from? What is the suggested "Action Required"?

Brash · ‎12-01-2022

Sounds like you're seeing this in action: https://community.meraki.com/t5/Security-SD-WAN/Flow-Preferences-ICMP/m-p/11354 Flow preferences do not honour ICMP (or rules that are "Any" instead of TCP or UDP.)

Brash · ‎11-30-2022

For the IP Access List that you have configured on the 3750, it's all IP traffic, not specific ports. So for the Port, you would use "Any" In regards to source and destination, it depends where your IP access list is applied in the 3750. You'll have to identify which interface/SVI it's applied to and whether it's applied inbound or outbound. Once you have that knowledge, you can then map the individual rules across to the Meraki ACL.

Brash

Community Record

Badges