Agreed and if the camera is a busy camera that is a lot of traffic. If you really need 4k you could possibly utilise the RTSP stream.  ... View more

beyond the 30, you will be cut off in the middle of the day.  That's what happened because the org was licensed through 2027, but the one device license was purchased but not applied.  Why you can claim a device and not the license bought together is beyond the understanding of the meraki licensing support engineer. ... View more

Hi,   you can also check if your carrier provides another APN that‘s not behind a CG-NAT and change your cellular gateway to it. This way you don‘t need to configure any manual NAT traversal rules. ... View more

The answer is yes, but it has nothing to do with multiple Ethernet ports. By "yes", I mean that you can configure it so that all traffic for an SSID goes to a seprate MX by way of a separate VLAN that is not configured on the primary MX or is not trunked to it. This approach requires L2 connectivity between APs and MX. ... View more

Good one. Thanks ... View more

The switch will also attempt to use DHCP over alternate VLANs, in order to obtain IP config and reach the Dashboard that way (it will then flag up that it's using that, rather than the configured VLAN). If your Core switch is configured for Layer-3 routing, remember that the management is separate from the user traffic (different VLAN)   https://documentation.meraki.com/MS/Layer_3_Switching/MS_Layer_3_Switching_and_Routing#Switch_Management_IP_and_Layer_3_Interfaces ... View more

Syslog is great, especially if you feed it into something like Splunk or an ELK stack. ... View more

Yes, especially when replacing MR52s and trying to reuse the three screws into the plasterboard ceiling that were fine for the MR52…  Not usable for a CW9166I!   Mind you, the CW9163E is even heavier, it feels like it is hewn from a solid billet of metal, lovely hardware! ... View more

I think it will depend on what you're looking to achieve from the integration. The standard set of Bluetooth tools are covered here: https://documentation.meraki.com/MR/Bluetooth/Bluetooth_Low_Energy_(BLE)#Bluetooth_clients If you need to explore anything else, in great depth, I suggest you reach out to your Meraki account team.    Contact details are available through the Dashboard under  Help (or ?)   Top right    > Get help >  Still need help? > Contact your Meraki sales representative ... View more

Hi Philip,   Thank you so much. I will check this out.   ... View more

Puede dejar el conmutador en el inventario; solo asegúrese de que no esté asignado a una red. ... View more

Ok, so Layer2 is out of the question.  That's fine.  These devices will connect to the server as long as there are routes setup.  So I can have the server on a different subnet, as long as it's in the same network.  Like, I think I should be able to do this through the site-to-site VPN.   ... View more

Initial provisioning can be done with a wired connection or a provisioning SSID.   Note you can only use a single MDM on a device.   Microsoft Intune has recently released an interesting option, Cloud PKI.  This should work with "Local Auth" certificate authentication on the MRs (disable passwords for this configuration). https://www.microsoft.com/en-us/security/business/endpoint-management/microsoft-cloud-pki  https://documentation.meraki.com/MR/Encryption_and_Authentication/Meraki_Local_Authentication_-_MR_802.1X#Certificate_Caching_(Certificate_Auth)  ... View more

As previously;  opening a case with Meraki Support is really the way to go with such things.   You're best off calling on the telephone, generally - email / dashboard takes a long time in back and forth questions and answers. Contact numbers are available via Dashboard:   Help (or ? top right) > Get help > Still need help? > Call the Meraki Support team ... View more

Yes exactly that.   Reserved IP is taking those IP addresses out of the DHCP scope. ... View more

@GreenMan is right. Be sure to use MST 0 (instance 0) for compatibility. This was discussed before on this other thread. ... View more

Thank you all for your information. Given the high costs, I think I will be sticking with the manual moving patch cables to the second switch.  ... View more

Indeed Phillip,  Sad but probably true... ... View more

With hindsight, you're right, sorry    (I only have an MG21 personally, where it is an LSP option). I raised this with product line and it is planned for addition to MG51 (and MG41) at some point, but with no fixed timeframe for availability, just now.   I have asked the team for an update, which I'll share when I can. ... View more

And udp/500.  🙂 ... View more

>the EC2 instance I cant ping back to an internal ip   Try temporarily disabling Windows Firewall on the internal machine to make sure it is not blocking the ping.   Make sure the on-premise MX has the VLAN where the internal machine is located included in AutoVPN.   ... View more

A factory reset will remove the config, but once the switch checks back in, it will re-apply the saved config assigned for that serial number, in the Network in which it's logically deployed.   If you want the switch to not load a duff setting, remove the duff setting in Dashboard, before it checks back in.   You may (also) find switches reverting to a locally stored Safe Config, if they can't get back to Dashboard any other way.   https://documentation.meraki.com/General_Administration/Cross-Platform_Content/Behavior_during_Connection_Loss_to_Cisco_Meraki_Cloud#MS_switch ... View more

@hillster do the drivers have a version number? ... View more

Yep, given the available info, I would say so  👍 ... View more

Raise a case with Meraki Support ... View more