New articles:
Change: New article.
Change: New article.
Security & SD-WAN:
Change: Added "Because of maximum firmware restrictions, content filtering no longer functions on several End of Support platforms that cannot run MX17 or greater firmware".
Change: Updated routing behavior between Auto VPN and IPsec VPN: "An MX Security Appliance can establish tunnels to both Auto VPN and IPsec VPN peers. An MX that builds tunnels to both Auto VPN and IPsec VPN peers will not route traffic between other Auto VPN peers and the IPsec VPN peers. The MX will send traffic to those VPN peers using the principles discussed above and in the MX Routing Behavior Document. However, an MX that builds tunnels to both Auto VPN and IPsec VPN peers, will only route traffic between the IPsec VPN peers and other Auto VPN peers if BGP routing over IPsec VPN is in use."
Change: Removed references of "public preview". The feature is now GA.
Change: Updated section "Configuring Intrusion Detection and Prevention".
Change: Updated section "Static Multicast API (requires 19.1+ firmware)".
Change: Added "Wildcard certificates are not supported at this time."
Switching:
Change: Added "All new networks created after August 1, 2025 will require a password to be explicitly set for Local Status Page access. Click here to learn more."
Change: Added "Cloud Monitoring End-of-Service Extended to March 31, 2026 : The end-of-service date for Cloud Monitoring has been extended by two months from January 31, 2026 to March 31, 2026, to allow customers additional time to complete their upgrade process. All other terms remain unchanged. Important note on C9500 series support: Configuration source: device (17.15.3+) does not yet support the C9500 series. Support for this model is planned and coming soon."
Change: Added "The maximum number of ACL's that can be configured in a single network is 128."; added "The VLAN field refers to the source VLAN for the traffic being evaluated and is processed on ingress."
Change: Added "The maximum number of ACL's that can be configured in a single network is 128."
Change: Added section "Cisco Optics Compatibility".
Change: Added "DO NOT claim the device using the Old version of the Inventory page."
Wireless:
Change: Added section "Note on Event Log Changes: Transition from AutoRF to Cisco RRM".
Change: Updated prerequisites: "Pending Public Release of Open Roaming New Architecture".
Change: Added "MR31.2.6+ // MR32.1.4++".
Change: Added "Currently this function is performed individually on the respective AP's from the Radio Settings page. At this time, we can not disable AP radios using an RF profile."
Change: Added "MQTT⁴"; added "AP Port Profiles (USB)⁴"; added "⁴MQTT & AP Port Profile with USB have been moved into the Meraki Advanced and Unified Advantage license tiers. Customers who have already enabled these features in their networks will continue to retain access."; added "²Intelligent capture and AI-RRM are currently at Early Access phase. There is no MR-ADV license required during the Early Access period."
Change: Added "USB AP port profiles require MR Advanced license tier.".
Change: Added "MQTT requires MR Advanced license tier."
Platform Management:
Change: Added "If a customer would like to convert back to co-term from PDL, please open a case with Meraki Support to perform the conversion."
Change: Added "Resetting the unit will clear the static IP address settings and local configuration of the device." to section "MR Access Points".
Change: Added "MT Credits", added "1x MT License".
Change: Added "We now offer 1 Free LIC-MT-E License with the purchase of each LIC-MR-A in subscriptions. Please not that this is not yet available for LIC-CW-A or EAs."
Change: Added "Requirements for Cloud Monitoring for Wireless Access Points".
Change: Updated Catalyst Center required versions: "Catalyst Center software update: Catalyst Center must be running 2.3.7.9 or 2.3.7.10."
