Meraki

Ryan_Miles · ‎Oct 31 2024

MV52 aperture is not user adjustable just FYI

Ryan_Miles · ‎Oct 31 2024

Can you provide some examples from this camera showing the plates? Feel free to block out some of the plate for privacy if you like. I have a MV52 set to 80% zoom and 1080p/high and can easily read plates at 250+ feet. Feeding this video into ALPR also deciphers the plates accurately. Are the vehicles in your scenario stationary or moving? And if moving, at what speed? Also, what are the lighting conditions?

Ryan_Miles · ‎Oct 30 2024

It's a bug and not intended behavior nor a supported feature.

Ryan_Miles · ‎Oct 29 2024

Maybe this has changed over time, not sure. Anyhow you can edit Sensor profiles including the Default profile for template bound networks. Sensor Alerts have always existed at the network level for template bound networks. The config doesn't live under the template.

Ryan_Miles · ‎Oct 28 2024

Traffic should route between VLANs by default. There are no deny firewall rules by default (aside from outside to inside.)

Ryan_Miles · ‎Oct 28 2024

There's no 3rd party recommendation. But the connectors are RP-SMA if you want to try something at your own risk.

Ryan_Miles · ‎Oct 23 2024

This is a known issue/open bug for the Camera list page

Ryan_Miles · ‎Oct 22 2024

The policy is outlined here https://meraki.cisco.com/meraki-support/policies/#product-end-of-life-eol-policy An end of support device will still connect to dashboard and function normally. As the policy states you wouldn't receive tech support on the device if you were to open a case online or by phone.

Ryan_Miles · ‎Oct 21 2024

Yes, but this is a different issue. Just creating this rule will cause the behavior.

Ryan_Miles · ‎Oct 21 2024

It's a known issue. I see it on my org too when I have SD-WAN rules configured. If you remove the rules the issue goes away.

Ryan_Miles · ‎Oct 21 2024

The MS220 only supports Ent licensing. You should be able to have both in the same org without issue.

Ryan_Miles · ‎Oct 17 2024

MG is a cellular gateway and can be configured in routed mode or passthrough. The default is routed mode and it operates as a simple NAT router. The WAN side is the cellular interface, the LAN side has a configurable subnet supporting DHCP and reservations. You would connect either of the MG LAN ports to a WAN interface on your PAN FW. Is this MG showing online from dashboard? If not that issue needs to be resolved first. I'd recommend verifying the SIM is active and engage Meraki Support.

Ryan_Miles · ‎Oct 11 2024

https://developer.cisco.com/meraki/api-v1/get-organization-appliance-vpn-vpn-firewall-rules/ You can use the API index to search on endpoints https://developer.cisco.com/meraki/api-v1/api-index/

Ryan_Miles · ‎Oct 10 2024

According to the doc Meraki APs do appear to use TLS for RADSec. And yes it appears ISE only support RADIUS over DTLS today and not TLS RADSec. Various docs don't seem to be all that clear on the topic.

Ryan_Miles · ‎Oct 8 2024

I used to have a MV32 mounted outside here at home. It got some dust inside and settled to the middle of the dome and was visible. I took it down and gave it a little shake and fell out or at least moved somewhere else no longer blocking the lens. You may want to start with that simple attempt. Not sure if there are any small openings on the camera to shoot some compressed air into it.

Ryan_Miles · ‎Oct 8 2024

Have you tested with the current stable 30.7? Same result?

Ryan_Miles · ‎Oct 5 2024

https://community.meraki.com/t5/Dashboard-Administration/Rouge-ghost-device-showing-in-firmware-page-OCD-kicking-in/m-p/216071#M7363

Ryan_Miles · ‎Oct 3 2024

https://getkap.co/

Ryan_Miles · ‎Oct 2 2024

Do you have more than 2 hubs? The add hub link goes away if there are no remaining hubs in the Org. Example

Ryan_Miles · ‎Sep 30 2024

Have you tried 30.6 and if so did it work? We state only approved antennas are supported and I believe this enforcement came in 30.7. https://documentation.meraki.com/MR/MR_Installation_Guides/CW9163E-MR_Installation_Guide#Antenna_Selection

Ryan_Miles · ‎Sep 29 2024

That's exactly it. MX100 has been end of sales for 3+ years and the recommended replacement is the MX95. If this was a replacement as part of a support case and the MX100 was in a HA pair they should send you two MX95s (and convert the license key in your dashboard).

Ryan_Miles · ‎Sep 26 2024

Could be a 30.7 issue. May want to test the latest 31.1.5 or have Support roll you back to a 29.x version at least to test.

Ryan_Miles · ‎Sep 24 2024

Does that model of iPad support OWE? I see the list of supported iPads mentions Pros, Airs, and Minis only. https://support.apple.com/en-my/guide/deployment/dep3b0448c58/web

Ryan_Miles · ‎Sep 24 2024

If you plan to manage these are Meraki APs in dashboard then you want the LIC-ENT https://documentation.meraki.com/General_Administration/Licensing/Meraki_MR_License_Guide DNA licenses would be for when running APs in Catalyst mode with a Wireless LAN Controller and DNAC/Cat Center.

Ryan_Miles · ‎Sep 24 2024

I'm awaiting a reply from MS PM about this. I agree the info is now scattered and difficult to read. For example the port mode, native VLAN, and allowed VLANs used to be all grouped together for a super quick visual review. The data is now spread across three columns. And as you said info is missing. Access Policy, auto speed rate, and STP state.

About Ryan_Miles

Ryan_Miles

Ryan Miles

Community Record

Badges