This actually happens. Once Chrome autofilled my account password in the SSID WPA2 psk passphrase.   What fun that was, changing the psk key on a country-wide deployment... Just disable form and pass autofill on the dashboard page (browser setting). I don't think it's the dashboard implementation that is the problem, rather than the browser filling in info where it shouldn't. ... View more

You think you can, but this is available only for 2.4GHz. Not possible to turn off 5. (At least on MR33s) ... View more

It seems to be better on beta 27.x  ... View more

I think CMNA is still available (I did it last year). As long as you refresh it every 3 years (virtual class), your license/support is extended. If this is valid https://community.meraki.com/t5/FAQ-and-other-resources/CMNA-Refresh/ba-p/38015 once you first refresh your CMNA your license will automatically extend.   There is no note for equipmnet replacement, but I suspect EoL equipment will be replaced with newer models when it fails, through an RMA. ... View more

Sometimes, you may need to open a case to support for this problem (provided your uplink doesn't block anything). ... View more

 @NolanHerring I’ve seen it a lot on PSK SSIDs on MR33. Can’t remember since when, but after wireless health was released, I was trying to investigate the Authentication errors.  Issue was seen on a lot of clients, even those who never changed their psk password. Obviously false positives, giving misinformation in the reports.  @PawelG i don’t thing it is roaming. I’ve seen it on single AP networks with static clients.  ... View more

Meraki and Umbrella integration goes beyond simply directing users to Umbrellas DNS servers. You will not need to block access to other DNS services, as this is done by the MR itself. You can read more below. https://documentation.meraki.com/MR/Other_Topics/Manually_Integrating_Cisco_Umbrella_with_Meraki_Networks#DNS_Traffic_Flow It works really well. With MR only or with MX.   However, if you do not to go into that deep of an integration (or using other DNS servers for filtering) you could simply block other DNS servers on the firewall).   ... View more

Testing it on my home lab for now... At least false authentication errors " Client entered wrong password." seem to have been resolved. ... View more

Unless something has changed since this https://nolanwifi.com/2017/02/06/merakis-mesh-mess/ Mesh beacon and (probably) network, is not affected by minimum bitrates (if you are thinking bitrates set on SSIDs). ... View more

Keep in mind that the mesh documentation does not recommend using a chain of repeaters. https://documentation.meraki.com/MR/Deployment_Guides/Mesh_Deployment_Guide#Maximum_mesh_hops The meshing algorith probably prefers a direct connection to the root AP if possible. ... View more

Usually on bad cabling, ethernet connections fall back to 10mbit half-duplex, which causes a lot of collisions on transmitted traffic. ... View more

That is your uplink ports to the internet. Did you check if a client connected to the switch gets an IP through DHCP and can connect to the internet? ... View more

So, if I understand correctly, there is only one subnet/vlan on your network. And the APs do not seem to get an IP through DHCP. If you are not using static IPs on the APs, maybe some networking problem?   Can you connect a laptop on a port that an AP is normally connected? Does it get an IP? Do you have Meraki switches between the MX100 and the MR32s? ... View more

If you are a Cisco partner you can go through your sales-order team for a trial (that's what we do). ... View more

Can you power cycle at least one of the APs?  Failures on updates can occur from time to time, but all of them at once is a bit odd.   In your case I would also check DHCP leases and ports the APs are connected to. The fact that some of the APs had turned to repeater mode before the update, mean that they weren't able to receive an IP through the wired interface. ... View more

Has anyone found anything else on this? I'm getting the same issue on 26.7 . The issue is seen on networks with a sinle AP (so no roaming issues) and on devices that have the correct key set. I think this is mostly seen on devices coming back from standby, but I'd have to do some wireshark captures to be sure. ... View more

This is a great way to troubleshoot the entire client path if needed. ... View more

Unless I am mistaken, you cannot see wireless statistics for connected clients. Systems manager, also not yet showing any info. ... View more

26.7 seems to solve issues we were seeing in MR33s. So far it seems good to deploy. ... View more

Once you enable sticky mac, check on the switch port config if the mac of the printer is added on the whitelist.   If you do not see the mac of the printer added, check with another device (laptop). If you see a mac added, check if it is the same with the printer. If it is not, delete it so that it can be automatically populated again.     ... View more

Still looking around the new app. Certainly an improvement over the old one. ... View more

I have not used one yet, but according to the install guide, there is no blue led status. https://documentation.meraki.com/MG/MG21%2F%2FMG21E_Installation_Guide Have you gone through the setup progress on the local page? https://documentation.meraki.com/zGeneral_Administration/Tools_and_Troubleshooting/Using_the_Cisco_Meraki_Device_Local_Status_Page#MG_Series Does the MG have a signal? Is it connected? Maybe the SIM has a PIN ? ... View more