Meraki

redsector · ‎Jan 3 2020

I did update all my switches from 11.29.1 to 11.30. No switch reboot was neccessary (no MS390 in use!). Everything works well.

redsector · ‎Jan 3 2020

I have got a lot of MR42 and had the same issue. After upgrading to version 26.6 everything works fine.

redsector · ‎Dec 27 2019

EU, Germany

redsector · ‎Dec 27 2019

That is strange, I got replaced a lot of this switches: I opened a case, they told me to do this and that. And then I got the replacements. I took a few days.

redsector · ‎Dec 27 2019

I have this issue sometimes when the MS225 are in a stack and connected with an aggregat to CIsco classic switches. I put an auto shut on error command on the cisco classic switches and after two minutes (120 sec) it´s doing a recovery then everything works well. Port-config: interface TenGigabitEthernet2/0/18 description to_ switch_18 switchport trunk allowed vlan 1,8,12,16,20,24,26,28,30,50,52,86,90,300,301 switchport mode trunk udld port aggressive channel-group 11 mode active spanning-tree guard loop global config for port-recovering: port-channel load-balance src-dst-ip errdisable recovery cause udld errdisable recovery cause bpduguard errdisable recovery cause security-violation errdisable recovery cause channel-misconfig errdisable recovery cause pagp-flap errdisable recovery cause dtp-flap errdisable recovery cause link-flap errdisable recovery cause sfp-config-mismatch errdisable recovery cause gbic-invalid errdisable recovery cause l2ptguard errdisable recovery cause psecure-violation errdisable recovery cause port-mode-failure errdisable recovery cause dhcp-rate-limit errdisable recovery cause pppoe-ia-rate-limit errdisable recovery cause mac-limit errdisable recovery cause vmps errdisable recovery cause storm-control errdisable recovery cause inline-power errdisable recovery cause arp-inspection errdisable recovery cause link-monitor-failure errdisable recovery cause oam-remote-failure errdisable recovery cause loopback errdisable recovery cause psp errdisable recovery interval 120 license boot level ipbasek9 diagnostic bootup level minimal

redsector · ‎Dec 19 2019

I am still waiting for Meraki multi VLAN bridging with their accesspoints. Cisco classic accesspoints can do. We need more than one VLAN to bridge for VoIP and cashdesks for mobile sales booths in our fun fair park.

redsector · ‎Dec 19 2019

Sometimes I get messages like "no connectivity" after an firmware upgrade. Usually there should be the message "Reboot (firmware upgrade)". I have this issue intermediant with MR accesspoints and MS switches. So, how can I be shure that the devices are really up to date? Can I trust the device overview page? The local device homepage doesn´t show the firmware version.

redsector · ‎Dec 18 2019

Hi, I did updates on all my networks with switch software version 11.29. Just finished a new release appeared: 11.29.1 I did an update on some smaller networks but they didn´t restart. Maybe my switches are not affected (MS220, MS225, MS120, MS250) to be restarted? Any ideas?

redsector · ‎Dec 13 2019

We had the same issue with 25.14. I opened a case, they said this is a known problem and should be resolved with 26.6

redsector · ‎Dec 13 2019

I had the same problem with my MR42‘s. A cold reboot helped. I opened a case: it seems to be a known problem with v25.14 and further. They say: with v26.6 the problem should be solved. I did update some smaller locations. No issue since then. I will update a big location at christmas.

redsector · ‎Dec 10 2019

First: an undo button Second: a multi VLAN bridging between MR accesspoints.

redsector · ‎Dec 10 2019

I have got one MR45 to test in a meeting-room connected with one gigabit to an MS225-48 switch. It‘s running well. The new apple iPhone 11 is running with wifi 6.

redsector · ‎Dec 9 2019

New accesspoints are having new issues. If you are patient you will get a stable MR45 after a few firmware upgrades.

redsector · ‎Dec 2 2019

Meraki told me to upgrade. With 26.6 it "might be better"

redsector · ‎Dec 2 2019

Which firmware-version are you running on ths accesspoints?

redsector · ‎Nov 25 2019

I have got many MR33, MR34, MR42, MR42E and MR52. Suddenly one of the SSIDs disappeared from some of our accesspoints. The accesspoints running MR25.14 software. After rebooting the SSID appeared again. I opened a case and sent some pcap-files. the answer was: this is a known problem and might be better with MR26.6 software. So I will update my accesspoints at chrismas and see whats happening.

redsector · ‎Nov 24 2019

Is it fixed with 11.28 ?

redsector · ‎Nov 17 2019

In Germany we have a tradition for the children waiting for christmas. They will get an advends-calendar at the first of December. And they are allowed to open a small door or a sac filled with small sweets or gifts each day. And this is what can be done with the Meraki devices sacs:

redsector · ‎Nov 11 2019

a cold reboot of the affected accesspoints did help. The hotline couldn´t help. They were asking for an capture file when the issues occures again. The reason for this issue is unknown.

redsector · ‎Nov 6 2019

Yes, it working again.

redsector · ‎Nov 6 2019

Today in different networks I can´t see connected clients in the accesspoint overview page. It shows "Current clients 0". In the accesspoints list it shows the number of connected cleints but not in the individual accesspoint view. A bug in the dashboard?

redsector · ‎Nov 4 2019

Is there a route to ip helper-address 10.1.0.35 because it´s on another IP range than the other addresses? interface Vlan2 description Users-OC ip address 10.10.100.1 255.255.255.0 ip helper-address 10.1.0.35 <----- ip helper-address 10.10.0.3

redsector · ‎Nov 4 2019

I have the same problem without solution: 2 SonicWall firewalls are connected to Meraki MS120 or MS225 switches. the link of the secondary firefall is going to "sleep" after an while. the switch says: port down. the firewall company says: "not our fault". In case of swapping the active firewall the link doesn´t go up and the network is disconnected. When I disable and re-enable this port (before the swapping) the link goes up (for a while).

redsector · ‎Oct 31 2019

@kYutobiyes all SSID´s are on 2.4 and 5 GHz. I opened a case at Meraki

redsector · ‎Oct 31 2019

Yes, but it´s beta and not stable. And it´s a very important location. So I have some fear to upgrade. And yes, I know the discussions about "beta" on Meraki devices.

About redsector

redsector

Markus Moses

Community Record

Badges