Meraki

MarcP · ‎May 22 2019

Organization or networks ? Networks will work by Auto-VPN. If you really want to have an IPSec Tunnel between different organizations, I don´t think this will work, without static IPs, as you will have to use "Third Party" VPN Settings.

MarcP · ‎May 21 2019

https://documentation.meraki.com/MX/Firewall_and_Traffic_Shaping/MX_Load_Balancing_and_Flow_Preferences#Internet_Traffic should be possible through flow preferences

MarcP · ‎May 20 2019

give them a call, so they will react directly on the phone.

MarcP · ‎May 17 2019

It is disabled... What about creating another hidden WiFi and tell them to use it?

MarcP · ‎May 16 2019

You should just forward this NAT to the device which is responsible for the subnet. Once I had szenario, nearly like yours, and have been told to do the following: Lancom --> Meraki --> Camera been told to configure the Lancom the Camera is "behind" the MX (configured next hop) and within the MX I did the forward, to destination. Should be the same in your case, but you have Meraki first and then something else. To be honest, it didn´t work at my scenario 😄 LINK to Post

MarcP · ‎May 10 2019

Maybe this helps: https://community.meraki.com/t5/Dashboard-Administration/Bulk-change-street-address/td-p/5921 Using API, but I´m not familiar with API...

MarcP · ‎May 7 2019

@CarolineS wrote: Hi @redsector - Thanks for the report! I've adjusted our community permissions configuration so that you (and everyone else, whoops!) can edit your signature again. Please let me know (on this thread is fine) if you encounter any further issues with this. Cheers! - Caroline @CarolineS It is working now. 🙂

MarcP · ‎May 7 2019

Good point, can´t find it as well. Looked here as well: The Meraki Community uses your Cisco.com account. To update your email or password, head over to Cisco Profile Management. Click on the "Personal" tab to update your email address, and the "Security" tab to update your password. If you'd like to update your Community Display Name, email community-help@meraki.net. But there is no signature setting as well.

MarcP · ‎May 6 2019

Thanks again to @MeredithW @CarolineS for making these kind of events! And Thanks for the prices 🙂 Very cool!

MarcP · ‎May 2 2019

@GavinMcMenemy wrote: I'm not sure I understand what you're saying. We have 2 SSIDs available and these are available on all APs. Wireless - Access controll, at the end of the site. He may thinks, the bitrate is configured, for example to 24, so 802.11b devices would not be supported EDIT: He edited his Post 😉

MarcP · ‎May 2 2019

Used a template for all of the MR´s? Or typed in all passwords manually? Fore sure you checked everything, just want to sort this out 😉

MarcP · ‎May 1 2019

yeah not the best solution at the moment. Do "make a wish", surely others did already. But right now I don´t see the point for having this ? Only thing you can do is to setup a template for future networks, where it is already configured.

MarcP · ‎May 1 2019

Well done to everyone, congrats to JimL, and Thanks to @MeredithW for making this kind of Contests 🙂 Edit: Forgot you @CarolineS , thanks to you as well, for sure 😉 Community will, for sure, stay even more active after this contest.

MarcP · ‎Apr 30 2019

what about walled garden? enabled?

MarcP · ‎Apr 26 2019

Think you should try to connect a laptop to the linksys first and see what kind of IP you get. Maybe the ISP just say they are using local IP Addresses. maybe the linksys is in bridge mode and forwards public IP addresses which can´t be handled by the mx?

MarcP · ‎Apr 25 2019

@kYutobi wrote: Just triple checked. That's odd because I could before it was attached to the switch. Thanks for clarification @MarcP Can´t remember I saw that anytime in the past 😄 😉

MarcP · ‎Apr 25 2019

Within Clients, you do not the the AP in Dashboard. I don´t see them there as well. at no site / network. You only see them in "Wireless -> AccessPoints" in Network Wide Clients you only see connected clients to the AP, with a Wifi sign

MarcP · ‎Apr 24 2019

Believe for all devices. Just open a case and let us know 🙂

MarcP · ‎Apr 23 2019

OK, got it now... quite easy, actually 😄 Create a scope for geofence (configure -> geofencing) and apply it to device with a tag, for example "recently-added" Go to Manage -> Apps , choose the app you want to geofence and add a "policy tag", thats it. Within geofence Within the App settings

MarcP · ‎Apr 22 2019

Thanks guys, I´ll check that today and let you know 😉

MarcP · ‎Apr 17 2019

Anyone any idea? You superusers 😉 @MerakiDave @BrechtSchamp @NolanHerring @PhilipDAth

MarcP · ‎Apr 16 2019

Hi, while doing a Webinar for SM, the speaker showed us it is possible to block apps, when you are out of range of a location. A example, an App was installed, when someonewas in the Headquater. When he was more away than 1km the app was uninstalled. After getting back in range of the geofence it was installed again. I can´t find where to do so. Can anyone advise? Thanks!

MarcP · ‎Apr 13 2019

Yeah really nice! Hopefully all will go on like this after the contest 😉

MarcP · ‎Apr 13 2019

Using I, not Hex was the Problem... :S why isn´t it possible to use the IP? Don´t get that.

MarcP · ‎Apr 12 2019

Very nice, looks great @msosa

About MarcP

MarcP

Community Record

Badges