Meraki

MilesMeraki · ‎Nov 15 2021

The following setup document outlines the steps for a vMX creation in Azure. In reality, when you create the network you could clone the network where your existing DC MX is sitting. I'd probably start with a greenfields design for the Azure side as I'd assume there would be some form of co-existence with the existing DC network and you'd therefore want to ensure there isn't overlapping addressing etc. https://documentation.meraki.com/MX/MX_Installation_Guides/vMX_Setup_Guide_for_Microsoft_Azure

MilesMeraki · ‎Nov 15 2021

Welcome!

MilesMeraki · ‎Nov 14 2021

Cisco Duo will enable the configuration of 2FA for Meraki MX client VPN. It's not supported by default, unfortunately. Heres's the DUO configurationdocument - https://duo.com/docs/meraki-radius

MilesMeraki · ‎Nov 11 2021

Check the Radius logs/logging on ISE and see if you're getting RADIUS logging attempts. If you are you can troubleshoot based on the error messages. If the logs aren't showing it could be that RADIUS isn't hitting ISE. I'd then look at any firewall/network changes which may have impacted the RADIUS traffic from APs to ISE.

MilesMeraki · ‎Nov 10 2021

Running DHCP on the local MX would be the way to go.

MilesMeraki · ‎Nov 3 2021

🍵

MilesMeraki · ‎Nov 1 2021

Have you looked at the Merkai Vision Portal/Vision app? https://documentation.meraki.com/MV/Viewing_Video/Using_the_Meraki_Vision_Portal_(Beta)

MilesMeraki · ‎Oct 25 2021

Hello and Welcome!

MilesMeraki · ‎Oct 13 2021

Weird... As far as I'm aware; The licensing structure for MX appliances is the same as that of any other Meraki device – 1:1 ratio of devices to licenses. Pair your chosen MX appliance(s) with the relevant license for your use case Enterprise license OR Advanced security license OR Secure SD-WAN Plus license More information on MX Licensing and features can be found here. https://documentation.meraki.com/General_Administration/Licensing/Meraki_MX_Security_and_SD-WAN_Licensing ENT is normally the base license. If you want Advanced Security or Secure SD-WAN Plus licensed features over the standard features then you would ONLY purchase this SKU. Not sure why the estimate calculator is showing this..

MilesMeraki · ‎Oct 13 2021

This Guide may help you to troubleshoot; https://documentation.meraki.com/MT/MT_Installation_Guides/MT_Troubleshooting_Guide I'd check a few things if it was working fine previosuly; - Doesthe new network have different firmware settings being applied to the MR access point? Is this set to 26.7+ Fimrware? - Is the MR access point being powered by the same power source? If not check to ensure the AP is running in full power mode. (Instructions in the KB article attached will help)

MilesMeraki · ‎Feb 24 2019

How is Building A the RSTP root bridge for the entire network? Remember RSTP operates at layer 2. Looking at your design you have Layer 3 throughout your network between the buildings. If the Layer 2 gateway for Building D + E is Building B This is the root bridge for those layer 2 networks. E + F Layer 2 Gateway is Building C. This is the root bridge for those layer 2 networks. Meraki switches have the ability to act as a layer 3 and can operate SVI's which can be used for routing/layer 3 purposes.

MilesMeraki · ‎Feb 24 2019

I'd, first of all, understand your STP topology and then work backwards from there. Do you have the Layer 2/STP topology diagramed/documented at all?

MilesMeraki · ‎Apr 10 2018

Congratulations @PhilipDAth! I wouldn't mind a free MR12W 😛

MilesMeraki · ‎Mar 27 2018

I Don't believe there is any "Hit count" counters for Walden Garden ranges. The only way i see possible to do this is to use syslog event logging for flows. Abstract that information and run queries on it to find out the ranges being used. Very time consuming and not the best solution! Why not "Make a Wish" in the dashboard for counters for Walden garden ranges?

MilesMeraki · ‎Mar 26 2018

Is this an MPLS WAN or DIA ISP connection? if DIA connection why don't you just plug the ISP's RJ45 handoffs directly into the WAN 1 and WAN 2 ports of the MX250? Assuming you're getting a single handoff for each ISP.

MilesMeraki · ‎Mar 20 2018

Interesting, I'd be keen to hear what others have to say, I'm clueless.

MilesMeraki · ‎Mar 20 2018

Congratulations to the community and all the members. I can't wait to be apart of the next goal an smash out 10,000 active members!

MilesMeraki · ‎Mar 19 2018

Is this on an MR network or MX? If MX, what do you have the traffic analysis setting set to under, network-wide> general traffic analysis? Looks like you can also enable "hostname" analysis for MR only networks via the same route.

MilesMeraki · ‎Mar 18 2018

Woohoo 🙂 Thanks, @CarolineS! Hopefully my CMNA badge will appear soon too!

MilesMeraki · ‎Mar 6 2018

Thanks for informing the community @HieuPhan

MilesMeraki · ‎Mar 5 2018

Awesome run down @PhilipDAth. I'm sure you voiced your opinion and looking forward to What's in store for 2018 🙂 I've had the pleasure of visiting Meraki HQ and can concur that it is a truly special place, filled with extremely bright people and amazing energy. I too look forward to re-visiting one day 🙂

MilesMeraki · ‎Mar 2 2018

Yes it will delete the footage. When you try and move the camera you're provided the below information.

MilesMeraki · ‎Feb 22 2018

To my knowledge, you can't clear the event log. Why would you want to anyway, you've provided it for security/auditing sake? I'd just disregard those entries.

MilesMeraki · ‎Feb 21 2018

😞 No Badges available for me. Living in the land of the long white cloud really does have it's negatives sometimes!

MilesMeraki · ‎Feb 21 2018

Man, I'm still yet to qualify for any badges! Better get registered to some form of Meraki training 😛

About MilesMeraki

MilesMeraki

Eliot Foye

Community Record

Badges