Community Record
48
Posts
27
Kudos
3
Solutions
Badges
Jun 24 2019
3:01 PM
1 Kudo
FYI, the certificate expires in about 26 hours....
... View more
Apr 10 2019
6:55 AM
1 Kudo
I have a similar issue, but a different error. When sending SMS i get an "Invalid" error. I have a case open, but no real progress yet.
... View more
Dec 6 2018
12:33 PM
1 Kudo
Keeping it on a managed switch will let you monitor how much bandwidth the other unit uses. If you go with a cheap unmanaged switch you can't tell who is using all the bandwidth later.
... View more
Nov 30 2018
2:14 PM
On the Cisco switch side the native VLAN would be 10 in this example.
... View more
Nov 13 2018
9:31 AM
@CML_Todd Be sure to get a demo and test it in your lab. We do some redistribution on the MS420s and they don't always act they way you think when you make a change to a route you are injecting into OSPF.
... View more
@Pete_RMOW when you are in the Routing & DHCP screen you can check the box next to an interface and then click Edit > Move and you can move the interface to another switch. The catch is you have to manually create the first interface before you can take advantage of this feature to move the others.
... View more
No, it only clones Layer 2 settings. The layer 3 settings can me "moved" to the new switch once you manually build the first L3 interface on the new switch.
... View more
Oct 15 2018
7:30 AM
Turns out the issue was with the AT&T Premier online order. Even though our admin got an email saying the SIM was activated it wasn't. After some tweaking on the AT&T site, the card eventually activated.
... View more
Oct 11 2018
6:00 AM
@nwu1 With the trial you have to provide your own SIM. Since I was out of the office yesterday, I left it in the office powered on all day and it did finally recognize the card. However, I took the 14.34 firmware update and it's working. Not sure if our cellular admin did anything to the cell plan.
... View more
Oct 10 2018
5:33 AM
Is there anything special I need to tell AT&T to get the SIM card activated in my Z3C? I've tried two new AT&T SIMs in a trial unit i have and the Z3C doesn't recognize them. However, if i pop the SIM from my cell phone in the Z3C it works fine. The new SIMs are activated in AT&T Premier. Thanks in advance!
... View more
Basically, all the hosts in VLAN 2 are on this switch. So trunking to other switches isn't an issue. One of the 3 devices in VLAN 2 has IPv6 connectivity and the switch AutoConfiged and is trying to talk to Meraki on that VLAN. This is not desired. I'm not sure why the switch even tried to auto discover IPv6 when it has IPv4 connectivity. At this point, no IPv6 connectivity for management is better than any IPv6 connectivity. I want to turn off IPv6 management, but i don't see where i can do it.
... View more
Above is the sanitized view when you click on the switch in the dashboard. Above is the view of the Auto configuration menu. No other options. Static IPv6 Address Assignment menu Above is the menu when you pick Static IPv6 assignment.
... View more
Yes, it has a static IPv4 address on our network management VLAN (which is the same VLAN as the one specified in Switch > Switch settings). The IPv6 address it picked up is on another VLAN. In the dashboard it shows the IPv6 address. My only options for IPv6 management address are AutoConfigure and static. The auto configure choice has no options (i can't tell it what VLAN to use). There is no off mode. I did open a case with Meraki, but so far nothing useful has come out of it.
... View more
Sep 27 2018
2:14 PM
Anyone else run across this scenario yet? We have an "unrouted" VLAN with an ISP device and the WAN ports of our MX warm spare pair connected to the same MS350 switch. Those are the only ports in the VLAN. The MS350 is not L3 enabled. Because the ISP is dual stack IPv4 and IPv6 the switch has used IPv6 Auto configure to grab a global IPv6 unicast address. Since this is a full Meraki network the switch is the only IPv6 device at the site. How can I make the switch stop talking IPv6 on the unrouted VLAN?
... View more
Sep 27 2018
2:09 PM
1 Kudo
Adam's correct. Clone only covers layer 2 portion. What you can do is enable Layer 3 on the switch device, then move the L3 interfaces over from the old switches. In the Switch > Routing and DHCP section. You'll have to build the first interface and set the default route before you can move/copy the interfaces and any static routes. You will also want to make note of any relay settings. In the early days those didn't move either. I can't remember if they move now.
... View more
Jan 10 2018
10:35 AM
If you want the AP to be on VLAN 11 and the switch port to use VLAN 11 as it's native (or untagged) VLAN, here's what you should try. Set the AP to DHCP and leave the VLAN tag blank. Then set the switch port to native VLAN 11. Then bounce the port. If the AP's configured management VLAN matches the native VLAN on the switch port you will get this error. The AP doesn't have a way of knowing what native VLAN the switch is configured for. In this case, it just knows that it's configured to use DHCP on a VLAN that it never gets traffic with the expected VLAN tag from the switch.
... View more
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 4593 | Nov 9 2018 9:14 AM | |
| 7792 | Oct 15 2018 7:30 AM | |
| 3123 | Oct 4 2018 8:44 AM |
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 2 | 3123 | |
| 1 | 25790 | |
| 1 | 3027 | |
| 1 | 2987 | |
| 1 | 4593 |
