Meraki

rwiesmann · ‎Dec 10 2020

Hi, I know this is an old entry in the community...just wondering I see in the summary report now CPU Usage, but on all my MX's it shows the message insufficient data....is this CPU usage still not there? Still it would be nice to have this information in real time...I do make a wish. rgds roger

rwiesmann · ‎Dec 10 2020

Hi all, I am just wondering if other of you experience the same issue. I have a MX 67 in place and I would like to use the packet capture function. Now every ones in a while it works quite well. Means I start it, I filter on a host and the output can be seen in the window below. But most of the time I start a capture and nothing happens except the the turning circle. Also if i start it and stop it again...most of the time no output but sometimes output will display. I am just wondering if this capture feature is not reliable or what could be the issue. I set even a filter to a host address in order that i will not have to much output. Intrested in your experience. rgds roger

rwiesmann · ‎Dec 9 2020

go for the green stars! Nice recognition.

rwiesmann · ‎Dec 9 2020

MV22 supports the sensors...see https://meraki.cisco.com/product/sensors/indoor-sensors/mt10/ You need to add the license key for the sensors in Dashboard in order to have the environmental option. hope that helps roger

rwiesmann · ‎Dec 8 2020

all good here...but I am on the European DC.

rwiesmann · ‎Dec 2 2020

Congratulation to all of you!

rwiesmann · ‎Nov 19 2020

Hi, i just had the same issue recently...how i solved it...I installed on the HUB site 2 MX's. One terminating the AutoVPN the other terminateing the non Meraki VPN. Had to create 2 organization...the routing between the 2 domains a have done on the lan side of the 2 HUB MX's. routing Meraki A (spoke) ----> Meraki B1 (Hub AutoVPN) <----------> Meraki B2 (Hub non Meraki VPN) ----> non-Meraki peer C site-to-site VPN rgds roger

rwiesmann · ‎Nov 12 2020

Hi, for Umbrella you need an advanced Licence. See also the following document: https://documentation.meraki.com/MR/Other_Topics/Cisco_Meraki_and_Umbrella_Integration_-_MR_Advanced%2F%2FUpgrade_License rgds roger

rwiesmann · ‎Nov 11 2020

Yes, there is. Go to Organization and then Change log rgds roger

rwiesmann · ‎Nov 11 2020

@BrechtSchamp just a small question to the document you linked here. For the MX it says "The default 4 hour reboot cycle has been removed for MX 14.35 & up, MX 15.11 & up, and MG 1.9 & up." Did they completely remove this reboot timer...or is there still such a function for MX 14.53?

rwiesmann · ‎Nov 10 2020

What is your question on it...licensing?

rwiesmann · ‎Nov 6 2020

That's what i was looking for...many thanks! rgds roger

rwiesmann · ‎Nov 4 2020

Hi all, does anybody know if there is a postman API Collection for Meraki on Version 1? Like the collection on Version 0: https://documenter.getpostman.com/view/7928889/SVmsVg6K I could not find it for version 1 thanks roger

rwiesmann · ‎Nov 3 2020

Well done and congrats to all of you 🏆

rwiesmann · ‎Oct 6 2020

Congrats to all!

rwiesmann · ‎Sep 2 2020

Well done! Congratulation!

rwiesmann · ‎Aug 4 2020

the orange one is the MG which is all fine if I go onto the device

rwiesmann · ‎Aug 4 2020

I have the situation, that under organization on the overview map it does not show the correct information. It shows in this case for a location an orange dot. On the same page on the Device List, the location is green. If i dive into the location, my MG is showing orange. But if i go onto the MG...all shows green.. Any ideas why this is? Are there different refresh timer? Or can I manually refresh the organization overview? Many thanks for your feedbacks roger

rwiesmann · ‎Jul 10 2020

Well deserved, congratulation @Network-dad and @DarrenOC !

rwiesmann · ‎Jul 7 2020

depends on how your setup looks like... but if you only have one vlan to the switch. assign the vlan, the according ip address and use access that's it

rwiesmann · ‎Jul 7 2020

choose under per port vlan settings the according port and push edit...in the menu you can define the vlan it should be in and if it is an access port or a trunk

rwiesmann · ‎Jul 2 2020

Check this document...it says that meraki licenses are intended to use by the original customer...but this does not really answer if you now own the HW and would like to buy a new license... I would, still open a support question and ask on how to proceed in this case.

rwiesmann · ‎Jul 2 2020

I guess you still will have the problem to claim the device...as it is still claimed in an other organisation.

rwiesmann · ‎Jul 1 2020

didn't try it in Barcelona...let's play this time!

rwiesmann · ‎Jul 1 2020

congrats to all of you...well deserved! keep providing answers and solutions!

About rwiesmann

rwiesmann

Roger Wiesmann

Community Record

Badges