About rwiesmann

rwiesmann · ‎08-26-2021

Not quite sure what you want to achive/replace. As I understand your setup... Internet Antenna then Meraki MX then Switch then AP But I am not sure if you need the USG to terminate the Internet Antenna...if so...you could place the MX just behind the USG Router. So it's depending what you would like to achive and which devices you need for certain functions. rgds roger

rwiesmann · ‎08-26-2021

Hi Abdikani, the MX65 is a Security and SD-WAN Gateway and not a switch. Check out the following link...you also can find deployment guides on this link https://documentation.meraki.com/MX hope this helps roger

rwiesmann · ‎08-25-2021

Happy Birthday to the Community! ✨ 🎈 ✨

rwiesmann · ‎08-10-2021

Congrats to all of you...well done and keep going!

rwiesmann · ‎06-30-2021

Hi, first of all...the setup check out this documentation for each OS. https://documentation.meraki.com/MX/Client_VPN/Client_VPN_OS_Configuration As a next step, check out this troubleshooting guide for ClientVPN. It helped me every time I had problems. Check the Event Viewer on the windows side and figure out what error code you get. With error code check the actions in the troubleshooting guide. https://documentation.meraki.com/MX/Client_VPN/Guided_Client_VPN_Troubleshooting hope this helps...or add more details roger

rwiesmann · ‎06-07-2021

Well done everbody and keep on posting!

rwiesmann · ‎06-01-2021

Hi, consolidate the following documentation on firmware upgrade. https://documentation.meraki.com/General_Administration/Firmware_Upgrades/Managing_Firmware_Upgrades In the following documentation you can see the best practices for MX'x. https://documentation.meraki.com/Architectures_and_Best_Practices/Cisco_Meraki_Best_Practice_Design/Best_Practices_for_Meraki_Firmware rgds roger

rwiesmann · ‎05-24-2021

Well, we should be able to do some test quite soon. @CptnCrnch thanks for you feedback and I try to give a feedback here.

rwiesmann · ‎05-21-2021

@CptnCrnch thanks a lot. Yes it helped for sure a bit. Like the route priority part. The routing also helped me a bit but still is not 100% clear. see picture IP routing will be undefined leaves a lot of interpretation...as it could work but is not clearly defined or it does not work... The availability is not an option, as my goal would be to load balance over the two non-meraki vpns. thanks a lot. Guess need to do some testing on it. rgds roger

rwiesmann · ‎05-20-2021

Hi all, wondering if someone has experience with Non-Meraki VPN to AWS....I know I could install a vMX and it would be easy. But my setup uses Non-Meraki VPN. AWS seams to have the concept of having 2 Tunnels. So on the Meraki side i configured 2 Non-Meraki VPN peers. AWS provides to different public IP to do so. This tunnels I terminate on the same MX. VPN status is green for both :). It also works, but I have some point which i do not understand. On the AWS side it looks like only one tunnel is active. Is this per design? On the Meraki side i provided the same subnets to be reachable over the 2 Tunnels on the AWS side. Does this automatically mean, the traffic will be load shared? Is it even possible to load share? One more question is, if I can influence the traffic to use a certain tunnel for an Subnet or even for dedicated traffic? Has anyone some experience on it? I consulted the Meraki documentation, but did not find any answers on this...or maybe i did not find the right documentation 🙈 rgds roger

rwiesmann · ‎05-05-2021

Just wondering if to this topic is some update? Is it still the way that i can not use a Meraki MX in Russia?

rwiesmann · ‎05-04-2021

April, April, well deserved all of you, congratulation!

rwiesmann · ‎04-26-2021

Hi, on the Switches...if you click on the port... You will get to the port information...under Status you will get some infos. But as far that I know it is not available for the MX's.

rwiesmann · ‎04-22-2021

You can move the license via a support case if you are admin. If you are not admin of the current organization you have your org admin can do this via the support case.

rwiesmann · ‎04-20-2021

@Inderdeep well done and congratulation!

rwiesmann · ‎04-15-2021

Check out this link about Meraki Now and advance HW replacement. https://meraki.cisco.com/product-collateral/meraki-now-at-a-glance/?file hope it helpd rgds roger

rwiesmann · ‎04-09-2021

good to start with the meraki documentation https://documentation.meraki.com/ For the MX you will have a lot of different topics in order to configure and what you need: https://documentation.meraki.com/MX Just to have it up and running use the quick start guide https://documentation.meraki.com/MX/MX_Quick_Start but all depends on what you would like to achieve?

rwiesmann · ‎04-07-2021

Congrats to all of you! No chance to pass the Top 4...but all 4 well deserved.

rwiesmann · ‎04-07-2021

Do you really need the MS350? There are also fanless models, like the ms120-24 https://meraki.cisco.com/de-de/product/switches/access-switches/ms120-24/

rwiesmann · ‎04-05-2021

Wow...so many winners...congrats to all of you and big thank you to @MeredithW for the bringing up this contest.

rwiesmann · ‎03-31-2021

Thanks for all your feedback. This is why I like this community 💚 ! Spoke Site is now upgraded and all working as expected 😊

rwiesmann · ‎03-31-2021

Thanks a lot for your valuable feedback @KarstenI, @UCcert and @cmr .

rwiesmann · ‎03-31-2021

I have a setup with a hub and about 25 spoke site (Auto-VPN). On the hub site i use a MX84, for the spoke site I use MX 67. Now I need to upgrade one spoke site to the stable rel. candidate version (15.52), because of a needed function. All the other MX's will stay on 14.53. Now, does anyone have experience with a setup where not all the sites do not have the same version? Interested in if VPN will work fine, any potential problems...

rwiesmann · ‎03-26-2021

congrats to all of you...just one step for me for tier 3 🙂

rwiesmann · ‎03-26-2021

Best is to upload the floorplans and place the AP's to the right location on the floorplan. https://documentation.meraki.com/General_Administration/Monitoring_and_Reporting/Using_a_Floor_Plan_or_Custom_Map_in_Dashboard Placing devices on the floorplans: https://documentation.meraki.com/General_Administration/Monitoring_and_Reporting/Placing_Devices_on_the_Map_in_Dashboard In Dashboard under Wireless => Heatmaps you will have this way the best results. rgds orger

rwiesmann

Roger Wiesmann

Community Record

Badges