Hi,  yes you can. See the following link. Just be aware that you can not mix advanced and enterprise licenses...either all MX's in an organization advanced or enterprise.   https://documentation.meraki.com/General_Administration/Licensing/Meraki_Licensing_FAQs   There is one question: Can I upgrade from Enterprise to Advanced Security or Secure SD-WAN Plus (MX Only)? Which explains it. Hope it helps roger ... View more

congrats to all of you, well done. ... View more

Like it, looks really great! ... View more

@DarrenOC, @CptnCrnch and @BlakeRichardson ... Thank you for all the nice and good feedback...still trying to clean up the 2000 mayhem 🤣 And also thanks to @MeredithW to be in the spotlight! 🙏 ... View more

Hi,  there is the alert for "the primary uplink status changes"...does this not help you? It alerts when the primary goes down and also when it goes back.   rgds roger ... View more

Check out this documentation about moving devices between orgs:   https://documentation.meraki.com/General_Administration/Inventory_and_Devices/Moving_Devices_Between_Organizations In short...the move of devices can be done by an organization admin. But be aware that Meraki Licenses can not be moved by the admin. You need to open a meraki support case.   Hope this helps. roger ... View more

Thanks to you @cmr, without your poste i probably would not have seen it. ... View more

Congrats to all of you, like to read you valuable posts, keep going! ... View more

done and only the bottle missing 😁 ... View more

intresting...could you post any update from the case here? ... View more

Like it! Thanks and congrats to all which have received it. ... View more

I was also looking for such information. Also some more infos to where a sensor is connected. Not much there. According to the Datasheet the data polling frequency is 2min, which would lead also to connection between the sensors and the gateway ....not sure if it is what you are looking for    see data polling frequency: https://documentation.meraki.com/MT/MT_Datasheets/MT10_Datasheet_-_Temperature_and_Humidity   hope it helps roger ... View more

Congratulation to all of you. I like to read your comments and solutions here every time. Well deserved and keep going! ... View more

you can give access rights either on organization level or network level. See the following documentation. https://documentation.meraki.com/General_Administration/Managing_Dashboard_Access/Managing_Dashboard_Administrators_and_Permissions   I tried to move the sensor to a dedicated network...but this will not work as long you do not have the device (MR or MV) to which the MT connects is also in this network. In other words. The MR's and/or MV's to which you like to connect the MT's need to be in the same network.   So you can restrict a dedicated user to have access only to MT's and the connecting MV's or MR's.. hope this helps roger ... View more

Check out this post: https://community.meraki.com/t5/Community-Announcements/New-badge-alert/ba-p/103335   The info provides also this email : community-help@meraki.net  if something not working in receiving the badge. hope it helps roger ... View more

@ww thanks for the information...as I do not have an MXw I did not know that RF Profiles do not work there. Thanks for the info. ... View more

Hi,  you can enable either the 5GHz and/or the 2.4GHz on a per AP basis in the RF Profiles.   See it in the documentation: https://documentation.meraki.com/MR/Radio_Settings/RF_Profiles   I am not sure if this is also possible in the MX67W as I do not have such an MX. But i would expect it. So on a per AP basis you can do it.   In your case you would need to go on a per SSID, where you can choose either dual band or 5GHZ only. So I would try to implement one SSID with only 5GHZ. The second I would try to configure dual band and just unassign all the channels of the 5GHz.   I am not sure if this will work...but I would try to do it this way. hope it helps      ... View more

hi,  usually a reboot of an MX goes quite fast if the internet connection is o.k you should be able to connect within 10 min I would say.   Did you change maybe the Uplink configuration and then reboot? There is a mechanism to revert to the last safe configuration...so if you change the Uplink and do a reboot and after the reboot there is no internet connectivity due to the uplink change...the MX will revert to the last safe configuration after some hours. See also: https://documentation.meraki.com/General_Administration/Cross-Platform_Content/Behavior_during_Connection_Loss_to_Cisco_Meraki_Cloud   rgds roger ... View more

Under Network wide => Clients you will have an overview of all client. There you also can filter on a network or policy base.     Not sure if this will help you, but hope so. rgds roger ... View more

Network wide => Clients. Choose the one you are looking for. Scroll down to Usage. There you will see the Usage of this client.     Hope it helps roger ... View more

Consider to check the licensing calculator....it's still beta but it maid help you. Only  for co-terminating licenses.   https://documentation.meraki.com/General_Administration/Licensing/Using_the_License_Calculator   still, I would remove devices which you do not use anymore from the inventory.   You also mentioned that you will add a 5y license for a MR46...if you add it there will be a new co termination date calculated for everything.   https://documentation.meraki.com/General_Administration/Licensing/Meraki_Co-Termination_Licensing_Overview/The_Science_Behind_Licensing_Co-Termination   hope this help's you ... View more

There are many tools available like   https://www.speedtest.net or http://speedy-de.ip-plus.net/speedtestJs/   hope it helps ... View more

@KarstenIdid happen to me also befor, but not this time 🙂 ... View more