Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About TBHPTL
TBHPTL
A model citizen
Member since Nov 6, 2019
Friday
Community Record
220
Posts
111
Kudos
4
Solutions
Badges
Jun 15 2023
5:22 AM
2 Kudos
It depends....Not all coax is equal. You must perform the calculations. I would use nothing less than LMR400 and you will most likely need lightning arrestors and you must account for signal loss for each connector and make sure your coax runs/legs are exactly the same length for each element. You may want to hire a professional. https://www.qsl.net/co8tw/Coax_Calculator.htm
... View more
Jun 13 2023
7:06 PM
4 Kudos
Be very careful when doing this as this allows not only bypass of the splash page ,it will also bypass any and all security you may have applied to the Meraki MR and MX. Its better to have custom group policy that adheres to the network rules but bypasses the splash page... or better yet a dedicated policy that allows only the access you need to allow for these macs. Allow List Applies the following settings to a client: Is exempt from all firewall rules, both Layer 3 and Layer 7 (Applies to both the MX Security Appliance and the MR Access Points) Bypasses AMP Bypasses a Click-through Splash page Bypasses a Billing (paid access) Splash page and access the network on an SSID without paying or authenticating Bypasses a Sign-on Splash page without authenticating (Applies to both the MX Security Appliance and the MR Access Points) Is exempt from Per-client bandwidth limit (Applies to both the MX Security Appliance and the MR Access Points) Is exempt from Traffic shaping rules (Applies to both the MX Security Appliance and the MR Access Points) Bypasses Content filtering on MX Security Appliance
... View more
Jun 13 2023
9:42 AM
The benefit is you choose the coverage pattern based on the characteristics of the antenna. It doesn't increase the increase the range per see, rather it transforms/"molds" the available energy into something that is more beneficial for a particular use / coverage case.
... View more
Is it truly separate "networks" or are the AP's in one physical location? Why do you need two differing RADIUS servers; is either RADIUS server not reachable from the LAN at either site?
... View more
How much do you want to bet?
... View more
Once again, ANYONE can be a service provider.
... View more
There are no lines to read between. I clearly and concisely stated there are caveats and it must be asked for. MSP portal is enabled by default. Configuring the MSP Portal An admin can create multiple Dashboard accounts using the same email address. When a new account is created using the same credentials, the MSP Portal feature in Dashboard will automatically activate and be displayed so the user account with access to multiple organizations can switch between them. There is no additional configuration necessary to enable MSP portal. https://documentation.meraki.com/General_Administration/Organizations_and_Networks/Using_the_MSP_Portal_to_Manage_Multiple_Organizations https://documentation.meraki.com/General_Administration/Organizations_and_Networks/Licensing_for_Managed_Service_Providers_(MSPs)_-_FAQ https://documentation.meraki.com/General_Administration/Organizations_and_Networks/Licensing_for_Managed_Service_Providers_(MSPs)_-_FAQ
... View more
Wired WiFi affects available your over the air bandwidth by 50% The whole half duplex thing..... A single mesh hop will cut that to one half and then another half of that for each hop. Run the cable or fiber, you will thank me later. 6 GHz will make this much less impactful but no outdoor 6GHz yet...
... View more
Everyone is mistaken. You absolutely can have an SSID only admin. Its a relatively new feature and there are some caveats but it is 100% doable. you have to ask for it and have MSP set up. SSID only admins: https://documentation.meraki.com/General_Administration/Service_Providers_-_SPs/Service_Provider_Dashboard_Roles
... View more
Wireless is at its heart Layer 2. Layer 3 is doable but causes lots of issues roaming, in particular with latency sensitive applications like voice and video conferencing. Go read this:https://documentation.meraki.com/MR/Wi-Fi_Basics_and_Best_Practices/Seamless_Roaming_with_MR_Access_Points
... View more
Jun 5 2023
1:26 PM
https://www.amazon.com/Solar-Controller-with-48V-PoE/dp/B00B11A5ZC Obviously you will need an enclosure for the solar controller battery etc. you will at the very least want one AP centered that is wired in to the network in close proximity. Mesh sucks no matter who the vendor is.... A
... View more
May 8 2023
1:24 PM
How about AFC with standard power and outdoor APs of any type, be they 6E or 7...
... View more
May 8 2023
1:21 PM
Relocate the MX at a point equidistant from its LAN connection that will make the cable run feasible for the MG or other cellular gateway cable run that you say is unreachable.
... View more
May 5 2023
2:51 PM
WPN via iPSK is the better option here, allows for more PSK then vanilla iPSK https://documentation.meraki.com/MR/Encryption_and_Authentication/Wi-Fi_Personal_Network_(WPN)
... View more
May 5 2023
2:39 PM
2 Kudos
The MA-MNT-ANT-2 is for mounting of antennas not an AP. the best way to mount any AP is horizontally suspended from the ceiling between 9 to 15 ft height from floor and below any obstacles like lighting fixtures architectural elements, ductwork beams etc. If you have open celling's then use conduit down rods to a single or double gang box onto which you surface mount the AP mounting bracket.
... View more
Apr 24 2023
11:46 AM
In this day and age of locally administered MACs you are going to drive yourself mad trying to block anything from the air. How are you granting access to the network? What is your Meraki hardware? MX and MRs, MRs only? etc... Your answer will determine what's available "canned" from the Meraki ecosystem for controlling access.
... View more
Flush and forget any stored profiles entries. THESE ARE EASILY CORRUPTED Update your client wireless drivers As a SIMPLE test you can change your PSK make sure that it is at least 8 characters in length and test... For the record just because a client doesn't move, that doesn't mean they will not roam. Clients, and clients alone, decide to which wireless AP they will connect.
... View more
Apr 14 2023
9:18 AM
it means that in order to join the network client device must be able to talk at 12 or 24Mbps 802.11b cant operate at 12 or 24 Mbps... 11b operates at 1,2,5.5, and 11Mbps. If you don't have 802.11b devices leave it at 12
... View more
Apr 14 2023
9:12 AM
"is having AP bandwidth that is greater than the total bandwidth our internet circuits provide pointless?" No its not pointless. You want your bottleneck (if you have one) to be your circuit not your medium of transport, in the case of the APs- the thin air... With Wi-Fi, the name of the game is get clients on and off the medium as quickly and efficiently as possible so the next device gets a turn.
... View more
Apr 14 2023
9:04 AM
Perhaps he means channel utilization... Which in my mind makes sense, likely the 2.4 sensor is nasty chatty....
... View more
Apr 7 2023
1:49 PM
Hamina is less money and is a very powerful web based predictive design tool. www.hamina.com
... View more
Mar 10 2023
3:12 PM
We go rid of 2.4GHz a long time ago. I can honestly say its has made the world a much better place. Have only had 2 complaints in 5 years.
... View more
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 3098 | Aug 14 2023 9:15 AM | |
| 1054 | Jun 27 2023 8:15 PM | |
| 712 | Jun 13 2023 7:06 PM |
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 12 | 4263 | |
| 4 | 5501 | |
| 4 | 8352 | |
| 4 | 812 | |
| 4 | 712 |
© 2024 Cisco Systems, Inc.
