Wow. Thanks team! and congrats to everybody else!  ... View more

Congrats to @alemabrahao, @rhbirkelund, @cmr, @PhilipDAth, @RaphaelL, @Brash, @van604 for reaching Tier 3. ... View more

Thank you Meraki Community, you are Awesome! ... View more

good idea to give it a reboot as well.   Usually I do not like the meshing feature and I normally turn it of.   https://documentation.meraki.com/MR/Wi-Fi_Basics_and_Best_Practices/Wireless_Mesh_Networking#Disabling_Mesh ... View more

@paulreveco - sorry to hear! Can you please send an email to our community team at community-help@meraki.net - we will get your badge sorted! ... View more

Awesome sauce! Thanks for all the contributions and the help! ... View more

The switch can reach the dhcp server via ping tests when sourcing from a stack interface ip in that vlan. What do you mean when you say is the switch an interface for that vlan? It's not the gateway if you're asking that. ... View more

Hi guys,   I tried the above but we're still experiencing this. To note it's only for new users trying to join Wi-Fi. The hops are still dropping at 10.128.128.128.   Any more ideas where to check? ... View more

Congrats to everybody for their contribution! ... View more

One more question guys. In regards to the new building. The fibre cable from this will be going to our art building. This has six spare cores that go back to the admin cabinet that has the core switch. Instead of getting a new core switch with more than four SFP ports would it be possible to just plug in the fibre cable from the new building into the spare SFP port in the MS225 switch that is in the art building. This will then just piggy back off this switch instead of going back to the core switch.  So the art switch will have the fibre SFP connection that goes to the Core and then also the fibre SFP connection going to the new building. Is this solution not really recommended? Thank you guys ... View more

I'll definitely agree that the dashboard is getting slower and slower...  ... View more

I connected it to the UTP port in front of the device, not the management port. ... View more

@Roey1984 it depends, take a look at the release notes, if you are experiencing any of the issues that have been fixed then it's probably a good idea to upgrade.  Otherwise maybe not. ... View more

Q: Did you have to reach out to your Cisco Meraki rep to unlock this?  A: No  Try to use -> Under Organization > Administrators  - > new section -> Update camera and sensor permissions ... View more

nice work folks, a lot of knowledge shared ... View more

Assuming your AP's are running off PoE from a switch, you could look at the switch logs (in case of Meraki - event logs) to see the last time that port transitioned state (Up->Down and Down->Up). A syslog would make this job much easier to consume the data and filter the noise. ... View more

Hey @Knowledge_gainr,    Thank you for those details!   If that is the case, a factory reset followed by a re-test may be in order. If that still fails, then I would advise giving the Meraki Support team a call so we can investigate the issue while someone is on site to make sure everything is in order.  ... View more

We have the same issue, all sites with a MG is Yellow but the MG it self is green and up and running.   Have you still the same issue 4 years later? 🙂 ... View more

Thank you and Congratulations to all the All-Stars!! A quality All-Star team ... View more

Congratulations to the winner 😆 ... View more

Congrats folks! Well done @Amit_pal! ... View more

@cmr / @DarrenOC - never fear, December MOTM will happen soon! We are recovering from the holidays & missing Amy 🙂 ... View more

Thanks heaps to the community. Great contest and so many great responses and looking forward to a new beanie.    I love it how so many are keeping up with their training and learning new skills. It's very easy to get stuck in a rut and avoid learning new skills.  ... View more