Meraki

MauroF · ‎Jul 5 2024

doesnt make lot of sense to be honest

MauroF · ‎Jul 5 2024

You are right but....if teh fortigate has a network untugged and the switch interface has a vlan 3 as native...it works....but AP side...if i set nativa vlan 3,trunk all.. doesnt work. it works when i use vlan 1 as native on the switch interface towards the AP

MauroF · ‎Jul 4 2024

Yes ,indeed although it is not explicitly mentioned.Thanks anyway.It worked.

MauroF · ‎Jul 4 2024

I need to Swap a MX64 with a MX75 on the same network but im concerned about a possible Client VPN issue. I mean..if the client connect to the hostname of MX..and i swap the firewall...is the hostname changing or it's going to keep that one? I mean: MX64 has a hostname: Test-mx01-edge-bkerjmtnkijc.dynamic-m.com if i swap the mx the hostame is going to stay the same? mauro

MauroF · ‎Jul 3 2024

Consider that when i typed the show meraki compatibility everything was compatible.

MauroF · ‎Jul 3 2024

HI all, i on-boarded my catalyst 9300 into the dashboard Meraki and everything went according to plan but once appeared in the Dashboard i received an alert saying "Device is running an unsupported firmware version." At the moment i have a "cat9k_iosxe.17.12.03.SPA". Whats the image range i need to have? Thanks

MauroF · ‎Jul 2 2024

The issue is that the switch Meraki even if i configured the vlan3 as native(management) on the switches..still have the vlan 1 as native bx default.. so the interface connected to a Ap see traffic not-tagged arriving from the fortigate and since the vlan native is 1 (default) it associated as it.What a shenanigan!

MauroF · ‎Jul 2 2024

Issue: my MR33 dont get an IP or sometimens they get it properly and afetr 30 sec htey get 1.1.1.1 Topology: Fortigate ---> switch----> AP Considering that i have a native vlan 3 (configured on my Fortigate L3) and my switch ports configuration are TRUNK,native vlan 3,tagged all. All the vlan are correctly configured everywhere i dont know what the issue is. But...if i change to config in the switch ....configuring native vlan 1 instead of 3, they get an IP. ideas?

MauroF · ‎Jul 1 2024

Hi all, i configured a Client VPN linked to a Radius serve(windows server 2016)r that use a AD as a database. At the moment it doesnt work. Is there a updated procedure to follow regarding this authentication Client VPN with NPS/AD? i checked this one : https://documentation.meraki.com/MX/Client_VPN/Configuring_RADIUS_Authentication_with_Client_VPN_IPsec but it doesnt work. Thanks in advanced. m

MauroF · ‎Jun 28 2024

HI, ive got a Vlan 20 where i have my servers.From the vlan 10 attached to the MX i need to ping a Client VPN but i cannot. Considering that firewall side i have all opened.. what it could be?

MauroF · ‎Jun 27 2024

i Already changed port, if i reload an interface the camera changes from 10 to 100M and viceversa...Software is the same,Switch is new.

MauroF · ‎Jun 27 2024

Hi , ive got an issue with my cameras Meraki MV33. basically i connected 10 of them and most of them reach 1Gbps auto-negotiation. few of them instead auto negotiate 100Mbps and 10mps. To be clear: it is not a cable issue.Important to know,Camera are working HD quality even if low band so i dont have a real issue. How is that possible? What could be the issue that differentiate one camera from the other? Thanks

MauroF · ‎Jun 19 2024

Thanks for the explanation mate!

MauroF · ‎Jun 19 2024

Hi, is there a way to create a L2 vlan on the meraki switch? i mean,the classic "conf t, vlan 10" on Cisco switches. I have a third party firewall connected to my MS250 which is my core. Im trying to understand how to configure it to create the layer 2 toward my access-switches (MS 120). I suppose i need to configure a TRUNK in the upstream uplink but how can i tag the vlan L2 in there if i havent configured them? Thanks. M

MauroF · ‎Jun 14 2024

You won the jackpot! Thanks pal! Configured and tested. Seems great!

MauroF · ‎Jun 13 2024

Yes,sure. Basically if i try from MAC i have no issue.. Couple of hours before a was showing a client the configuration of my VPN. Since i wanted to show how it was done from the scratch i deleted the VPN and started to re-create. I configured it like the previous one. Tried many times to connect but couldnt. After 20 minutes trying do understand i decided to reload the laptop. First try i was connected. My client has got lots of this issue...all with Windows...and al work perfectly after reload.

MauroF · ‎Jun 13 2024

Ive got this issue: i configured a VPN using the built-in configuration on Windows. Sometimes doesnt work and need to reload to make it work. I wonder what other alternative i got that can be compatible to connect remotely to VPN Meraki. OpenVPN doesnt seem to be the correct one and not willing of configuring Anyconnect at the moment. Any other option can download and test? thanks Mauro

MauroF · ‎Jun 13 2024

Best exclamation i could get! Thanks very much for your help and your time.Everything is clear now.

MauroF · ‎Jun 12 2024

I probably understood what you mean.. You are saying that if i move from A to B... in B the configuration will be empty. Thats ok,i knew that but thanks fro telling me again. I already configured the B organization with the same configuration i have in the MX in the Org_A so moving from A to B and B to A would be kinda transparent

MauroF · ‎Jun 12 2024

"the device just won't change the settings." what do you mean with that? My question was about keeping the configuration of Vlan/static route/ipsec admin/Guest in case of roll-back. can you elaborate on what you said? I appreciate the effort to help me mate 🙂

MauroF · ‎Jun 12 2024

i just did it right now. - Remove appliance from network on org A - organization ---> Inventory o org B and add the MX on the new Network. -rollback removing MX from network in org B - organization ---> Inventory o org A and add the MX on the old Network. under Addressing & VLANs i still have the old vlans configured.

MauroF · ‎Jun 12 2024

Are yous sure? im testing in my lab this thing and it keep all configurations.

MauroF · ‎Jun 12 2024

What im interested the most here is that if i move from A to B and then rolingback from B to A it keeps the configuration pre-activity in the A org

MauroF · ‎Jun 12 2024

i all, im planinng to move my MX to another organization. In a roll-back scenario ca i just unclaim the new MX from the NEW org and claim it back to the OLD keeping all the previous configuration?`Im afraid that during the first movin, meraki woudl delete all my MX configuration (Vlan,static route,Client IPsec etc). Any experience with that? Thanks.

MauroF · ‎Jun 4 2024

So you are saying that....when i remove the network from a MX and i claim it in the new organization, the connectivity should work fine without any othe configuration on the WAN Public interface?is that correct?

About MauroF

MauroF

Greg

Community Record

Badges