Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About latintrpt
latintrpt
Getting noticed
Member since Oct 27, 2021
Feb 13 2023
Community Record
21
Posts
4
Kudos
0
Solutions
Badges
Feb 13 2023
11:06 AM
Hi alemabrahao, does this mean that Meraki support would not assist with troubleshooting in case of issues?
... View more
Feb 13 2023
10:43 AM
Hi, I have a site that uses MR84's and need to purchase additional AP's to fill in some gaps in coverage. Does anyone know if the MR84's are compatible with MR86's? Any roaming issues? Thank you
... View more
Labels:
- Labels:
-
Installation
Aug 7 2022
2:49 PM
Thank you for the information? Any other configuration required to get this to work? Another silly question, if the MX has never connected to the cloud, how will it know to pick up the VLAN config of the switch ports?
... View more
Aug 5 2022
3:09 PM
I took an available IP on the /30 of my ISP's WAN subnet. Do I also need to create a default route pointing to the WAN IP on the ATT side?
... View more
Aug 5 2022
2:37 PM
I've done the above and put it on VLAN 999 but it does not work. Any other configuration that is needed?
... View more
Aug 4 2022
2:21 PM
So using the 3 live AP's below as an example on 5 GHz using the default antenna in Meraki MA-ANT-20 7 dBi configured but I really have a AccelTex ATS-OP-245-13-4NP-36 13.0dBi installed, what would be my true transmit power's or is what is presented below the true transmit power?
... View more
Aug 4 2022
12:12 PM
I should re-phrase my question, if I leave the default antenna (MA-ANT-20) which has Gain (5 GHz): 7 dBi, does that mean that the AccelTex AP will be limited to 7 dBi gain instead of 13 dBi on 5 GHz?
... View more
Aug 4 2022
10:50 AM
What would happen if I leave the default value and I am using say the following antenna? AccelTex ATS-OP-245-13-4NP-36 13.0dBi
... View more
Aug 4 2022
9:15 AM
Hello, I added a non-standard Meraki antenna to a Meraki MR86. My question is, how do I account for antenna gain if the antenna won't appear in the dashboard? I have already set an RF profile to account for min/max transmit power. Thanks
... View more
Jul 13 2022
10:04 AM
Hello, I've been presented with a challenge. We have been provided a fiber handoff from our ISP to plug into our Meraki MX100. The only issue is that the MX100's internet port is a ethernet. Is there anyway to use an SFP port on the MX100 to make this work? If so, how would I need to configure this? Thanks.
... View more
Jun 23 2022
2:11 PM
Awesome, I appreciate you explaining and showing me the configuration.
... View more
Jun 23 2022
2:00 PM
Yes I do. On the MX I have a static route to the Sonitrol panels network with next hop being MS via a transit VLAN Can you show me how the configuration should look for on the NAT based off the firewall requirements above?
... View more
Jun 23 2022
11:18 AM
2 Kudos
Thank you. Which access policy type would be most relevant for my situation of wanting to authenticate based on MAC address and certificates?
... View more
Jun 23 2022
9:17 AM
Hi there, I have a requirement that I need to meet where if I have a client that plugs into the wired network, that they are placed on the correct VLAN based off their MAC address, certificate, or the OUI of their MAC address. I have MS250-48FP switches that these devices will be plugging into. There is another tech that will be working on the radius side of things, but I was wondering if this was possible on Meraki and if I need to do anything on Meraki side to get this to work. Thanks,
... View more
Jun 23 2022
9:06 AM
Anyone that can help out or have any ideas? Do I even need a port forwarding rule in place on the MX?
... View more
Jun 22 2022
4:41 PM
Hi, I have an MX100 that is connected to a Layer 3 core MS250-48FP stack. I'm trying to setup port forwarding for a client I have on my LAN (Sonitrol Panel) with the following requirements: Since my MS is doing the routing for the panel VLAN, how would I set this up or would I need to move routing to the MX for this VLAN? Also, how would the port forwarding rule look like on the MX? Thanks
... View more
Jun 18 2022
9:05 AM
Hi there, I have a Meraki MX that is my firewall connected to a pair of MS switches doing my layer 3 routing. I have to configure a VLAN with the following for AV equipment. This traffic does not leave the VLAN. DSCP Queue Values: 56(CS7) - Highest(8), PTPv2/timing, microsecond requirements 46(EF) - Medium High (6), Audio, in sequence 26(AF31) - High (4), Camera Video, MP4/h.264 IGMP Requirements: Version 2 IGMP Querier on subnet IGMP Snooping Enabled on ports & VLAN Fast/Immediate-Leave enabled on ports & VLAN for Camera switching Can anyone tell me how to set this up? Thanks,
... View more
Oct 28 2021
1:48 PM
Thanks for this information. I was looking at the two different dipole antennas offered by Meraki: MA-ANT-3-A - not bendable MA-ANT-3-B - bendable You mention vertically pointing the antennas if I place the MR46E on the wall. Since the MA-ANT-3-A are not bendable, how would this be done?
... View more
Oct 27 2021
8:40 PM
Hello, I have an area where I cannot mount AP's on the ceiling. My next option is to mount them on the wall, but I'm looking for a the best recommendation of AP with either the MR44 or MR46E with dipole antenna. I'm just looking for omni directional coverage in this particular area. Any suggestions? Thanks
... View more
Labels:
- Labels:
-
Installation
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 2 | 1261 | |
| 2 | 2875 |
© 2024 Cisco Systems, Inc.
