Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About JPScolar
JPScolar
Here to help
Member since Apr 23, 2021
Oct 30 2024
Juan-Carlos Perez
Canada
Community Record
21
Posts
0
Kudos
1
Solution
Badges
Hello, We would like to use digfital certificates instead of login credential for Wi-Fi Access. Any advise, in addition to the Meraki documentation, on how this should be implemented, what pitfalls to avoid, best design/strategy, , comments about cost (recurrent cahrges), and security will be very much appreciated. Thanks in advance.
... View more
Labels:
- Labels:
-
Installation
-
Other
-
SSID
Jun 18 2024
2:34 PM
Hello, What kind of reporting/visibility can we get on the Meraki Dashboard related to the Access Point Advance Security license for the Wi-Fi APs? Is there a way to get some reporting/visibility on the activity of the Advanced License? Thank you for your help.
... View more
Labels:
- Labels:
-
Other
Jan 3 2024
11:00 AM
Hello, What's the best way to interconnect 3 x MS120-24P switches to VMware SD-WAN VCE and provide some level of redundancy fo the access ports? I cannot use 2 x MS120-48 ports. LAN devices are organized in multiple VLANs Thank you for the comments and advice.
... View more
Labels:
- Labels:
-
Layer 2
Oct 29 2023
7:56 AM
Hello, Is Dyanamic routing on the MX supported in NAT mode or only on VPN Concentrator mode? I have heard that the BGP support on the MX is lacking a bit, for instance to set eBGP connectivity to non-Meraki networks. Any comments/advice on this? Thank you.
... View more
Oct 2 2023
3:54 PM
I went through that document but it doesn't show how to to do for a Warm Stand-by system (HA). Also, I have a question with this setup. Assuming my DMZ server has a public IP which Im NAT'ing 1:1 to my active MX public IP. This will be ok for sessions initiated from the DMZ server towards the Internet but for outside sessions trying to reach the public IP Address of my DMZ server, and assuming my MX Public IP is provided by a different ISP from the ISP providing the DMZ server public IP, then sites out on the INterenet will never be able to reach my DMZ Web server.
... View more
Oct 2 2023
2:20 PM
Hello, I have this MX-100 HA site and I need to adda DMZ (services to be advertised on a public IP which s behind the MXs). How should this be configured and wired? I have the Meraki doc t set up a DMZ but this assumes only one WAN connection. Thank you very much for your advice.
... View more
Labels:
- Labels:
-
Other
Sep 28 2023
7:22 AM
Any advice on how to build a DMZ with a MX105 in High-Availability mode will be very much appreciated. How the Public IP addresses for the services in the DMZ behind the MXS should be routed? How the MXs should be configured for this purpose? Thanks in advance.
... View more
Sep 16 2023
4:22 PM
As per the Meraki documentation, I can extend the VPN to to Azure while providing high availability as per the attached picture. If understand correctly I will need an separate VNET for the vMXs, a virtual Firewall (here I'm assuming it will be a Azure virtual FW) and the Virtual WAN Hub. The vMX will be medium size. What could be the ballpark recurrent and non-recurrent costs to set this up? Does each vMX needs a separate FW. Meraki documentation mentions the vMXs must be in different regions. (two different concentrators, if the first one fails, the hbrenches will route traffic through the other VPN concentrator and not a active/stand-by high-availability mode). Thank you
... View more
Labels:
- Labels:
-
Azure
-
Cloud networking
-
Virtual firewall
Sep 7 2023
3:04 PM
PhilipDAth. Thank you for your comments. So, basically the vMX Sjould remain as VPN Concentrator, right? How about the Firewalling? I would need a FW inf front of the vMX. Or if this is only Auto-VPN tunnels, could I get by without a firewall?
... View more
Sep 7 2023
8:44 AM
Hello, I want to migrate a Cisco DMVPN network to a Meraki MX SD-WAN network. DMVPN main hubs are at a Service Provider Data Center, which in turn, provides an Express Route connection to an Azure private cloud where all services are located. I would like to build an vMX VNET at the Azure Cloud and use BGP to route to other VNETs (workload). This way I will remove the Service provider dependency. Any advise, comments, suggestions on the diffificulties of implemnting this type of network. Any thing in particular I need to pay attention to? Thank you for your help.
... View more
Labels:
- Labels:
-
Auto VPN
-
Azure
-
Client VPN
-
Firewall
Jul 27 2023
7:50 AM
javalins, I'll try that. Thanks for the advice.
... View more
Jul 26 2023
8:44 AM
Is there a simple and quick way to get produce a report to tell me how many MX devices are using? * Their embedded LTE module for Failover. * An external CradlePoint device on WAN2 for Failover Thank you.
... View more
Jul 10 2023
7:52 AM
Hi Alemabrahao, I understand the V and H plane perspectives and omnichannel vs directed patterns. What I'm trying to understand is: A) how the scale in the polar diagram co-rellates to the gain in the datasheet? For instance, in this graph, on the H-plane I see a max gain of 10dbi at any angle but the datasheet is saying a 3 dbi gain @ 2.4 Mhz. B) what the normalized scale on the left (vertical bar) is telling me? and how does it correlates to the polar graph to the right? Can you help me with that? Thanks.
... View more
Jul 10 2023
6:55 AM
Can you elaborate a bit more? I see the polar diagrams but how does that answer the questions I'm asking? Thanks.
... View more
Jul 6 2023
9:12 PM
Hello, How to read/interpret the Antenna Radiation Patterns in the Meraki Datasheets. For instance, Dipole MA-ANT-3-B5/6 has a Gain of 3 dbi (2.4Mhz and 5.7 dbi (5Mh). The H-Radiation diagram shows a a circle (this is an omnichannel antenna) with a diameter of 10 dbi at all angles and all the inner circles have decreasing dbi. How the '10' relates to the 3 and 5.7 Gain? I assume moving towards iiner circles represents loosing Gain. Also . there is a Vertical scale to the left of the polar diagram called 'Normalized Gain' How does this relates to the Radiation/ Polar Diagram? Thank you for your help.
... View more
Labels:
- Labels:
-
Other
Jun 8 2023
7:21 AM
My client wants to keep its Watchguard firewalls behind the MX appliances because he wants to control its network VPN remote access for its organization while benefiting of the SD-WAN advantages. For this he will need a Public Static IP address for the firewall but I think this is difficult to implement behind the MXs. In addition, at its DC facility, we will have two MXs in High-Availability mode so changes on the IP address while on failover mode make break the Firewall VPN tunnels. Any advise on the best possible architecture to cope with this situation? Thank you for your help and comments.
... View more
Labels:
- Labels:
-
Firewall
Jun 1 2023
8:08 AM
Hello, I need to produce reports on the Active & Failover links performance on a given time period. Something like: Network Name | WAN Link Name | UPSpeed | Down Speed | Overall Data usage | Avg Throughput | Avg Packet loss. Insight produces some of this information but I need a license and I cannot export the info on a spreadsheet for further analysis. Has anyone done something similar through APIs? Any advice? Thank you
... View more
Mar 28 2023
10:48 AM
Any tool, application, method to produce Wi-Fi heat-maps for the MR APs before deployment? Thank you
... View more
Mar 21 2023
1:23 PM
Hi PhilipDath, Thank you for the reply. That seems a interesting idea. What will be the advantage of stacking, say 2 MS225, to build a core vs connecting all MS225 directly into the MX250s?
... View more
Mar 21 2023
9:50 AM
Thank you for the pointer. It is useful information. My problem is that the Access Switches may be a bit of an overkill for the MXs and WAN uplinks and I'm trying to figure out the best possible design given these constraints.
... View more
Mar 21 2023
8:49 AM
I have 2 x MX-250 in HA mode with 2 x 1Gb WAN uplinks and 10 x MS225-48 port switches. I don't know yet if the local traffic is more north-south or east-west and I'm trying to figure out the best switching design. * Do I need an additional aggregation switch, if so, what architecture will be more convenient? Spine-Leaf or 3-Tier? * What aggregation switch will be most appropiate, a MS425 (10Gb aggregation), using SPF+ ports as uplinks to the MXs (is this possible)? * Will it be a better idea to connect aal MS225 directly into the MXs using the SFP+ ports? Thank you very much for your help.
... View more
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 1753 | Jul 27 2023 7:50 AM |
© 2024 Cisco Systems, Inc.
