In addition to @PhilipDAth observations, I advise you to hire a specialized consultancy. Despite being something relatively simple, without the technical knowledge it can make things "painful" ... View more

No, it wouldn't. It is not just neighboring APs that increase channel utilization.   The number of connected clients, the number of SSIDs, the amount of data being transmitted, all of this directly collaborates in the use of the channel, and speaking of 2.4Ghz it is even worse for having only 3 usable channels available.   Do you want an advice? Migrate to 5Ghz if possible. ... View more

In that case there is nothing to do but try to find out who your neighbor is and try to talk to him. Good luck. ... View more

I suggest you open a support case. ... View more

Yes, end of support will end in 2027.     ... View more

The answer is not. ... View more

Check it at the documentation.   https://meraki.cisco.com/product-collateral/ms-family-datasheet/   You can use a power injector too. ... View more

Take a look at the documentation, there are some considerations. If you have LACP configured on the ports that MX is connected it will not work.   LACP & Link Aggregation The MX does not run LACP or any link aggregation protocols. Connecting aggregated ports to the LAN of the MX is not supported; all connected ports should be un-aggregated. If multiple ports are connected to the MX from a single switch for redundancy, it is highly recommended that you run STP on that switch, to ensure that one of the redundant ports is safely put into a blocking state. ... View more

Take a look at the documentation.     https://documentation.meraki.com/Architectures_and_Best_Practices/Cisco_Meraki_Best_Practice_Design/Best_Practice_Design_-_MX_Security_and_SD-WAN/General_MX_Best_Practices#High_Availability_and_Redundant_WAN_Connections   https://documentation.meraki.com/MX/Networks_and_Routing/MX_Layer_2_Functionality#Spanning_Tree_Protocol_(STP) ... View more

Check the installation guide:  https://documentation.meraki.com/MG/MG_Installation_Guides/MG51%2F%2FMG51E_Installation_Guide#Setting_up_Cellular_Connection ... View more

I Suggest you open a support case. ... View more

Take a look at the documentation.   https://documentation.meraki.com/MX/Networks_and_Routing/Configuring_VLANs_on_the_MX_Security_Appliance ... View more

I don't see a huge benefit to using full mesh. The biggest and only difference I see is that the MXes will have a direct route to each other, without the need to go through a specific HUB. In most deployments I've seen the most common is to use hub and spoke. ... View more

why a duplicate answer? ... View more

If you have a single standard configuration for all your newtorks, definitely using templates is the best option.   Imagine if you had 500 networks in your organization, wouldn't it be easier to apply the settings in a single place instead of configuring them in each network?   The update issue may seem worrisome initially, so what you can do is choose a location that is not so critical and not add it to the template, then you can update that location first and do the necessary validations before updating the entire template. ... View more

Is disabling device sleep an option? ... View more

First time I hear about a supplier installing equipment inside the infrastructure.   A network for consultants is usually used and policies are created on what should and should not be accessed. ... View more

I suggest you open a support case. ... View more

There are no special settings for this. I believe that Twilio's support is giving some excuse, on Meraki's side it's a simple Account SID and Auth Token configuration, it doesn't make sense to have to configure something like that on Meraki's side.   https://support.twilio.com/hc/en-us/articles/223181068-Sending-SMS-messages-to-countries-where-Twilio-numbers-aren-t-available ... View more

If It's on a template yes. ... View more

I had some issues with version 18.107.2 regarding printers. I suggest you to downgrade to some other version available in the dashboard. If this is not possible, I suggest opening a ticket with support. ... View more

Check the full documentation on the link above. ... View more

Configuration Overview The following steps outline the required configuration (both in Dashboard and Active Directory) to allow for AD-based group policy application. Please be sure to follow each step as accurately as possible, errors can be difficult to diagnose and resolve. Create an Active Directory site for the MX so users authenticate against the correct Domain Controllers. Enable security auditing on Active Directory Domain Controllers so the MX can obtain all relevant logon events. Enable the Global Catalog role on each Domain Controller because the MX uses LDAP/TLS over TCP port 3268. Install a digital certificate on each Domain Controller for LDAP/TLS. Certificate Requirements for TLS Create groups in Active Directory which will be mapped to Group Policies in Dashboard. Add users to groups in Active Directory.  Configure Group Policies in Dashboard. Configure Active Directory Authentication in Dashboard. Create LDAP group to Group Policy mappings in Dashboard.   Multiple Language Server Support The support to query Microsoft Active Directory servers configured for non-English languages is presently not supported. This functionality is currently under consideration by the Product and Engineering teams. We do not have an ETA on implementation.     Full doc: https://documentation.meraki.com/MX/Content_Filtering_and_Threat_Protection/Configuring_Active_Directory_with_MX_Security_Appliances ... View more