@gingerbrown and of course i am with @cmr on this, make sure deal with the previous owner and we will be happy to assist you in any situation if we can : ) ... View more

Well you need to have admin access to the switch via dashboard, there are three things before we go anywhere else with this problem  1) No link lights when connecting a device to an Ethernet switch port  We need to check, Switches > Configure > Switch ports, clicking the port in question and check for port status ( Enabled or disabled)   2) Switch doesn't recognize a connected SFP module As you said, it is already compatible,  the status of that module can be seen in Dashboard under  Switches > Monitor > Switch ports  by looking at the port    3) No power delivered to a connected Power over Ethernet (PoE) device PoE can be enabled on a switch port in Dashboard under  Switches > Configure > Switch ports ... View more

@gingerbrown : Can you check the port there is enabled or disabled  Switches > Configure > Switch ports ? ... View more

@SeaTec : Glad you restore .. not sure but may be flushed out ! ... View more

So did you connect correct ? ... View more

@SeaTec Can you restart the DHCP services once.  ... View more

@gingerbrown : So how are you connecting, One end to Meraki MS220 and other end to your streamer ? Am i correct ?  Can you have two fiber strands, flip them on patch panel . sometimes we put like TX going to RX and RX going to TX. ... View more

@gingerbrown : Can you share the SFP model you are using and Is that compatible with Meraki ?  Check below the various SFPs supported  https://meraki.cisco.com/lib/pdf/meraki_datasheet_sfp.pdf   ... View more

@CarolineS : This is awesome, cool.. Thanks a lot for these changes ! ... View more

@tombaz47 : Yes you can probably do that as @MarcP said, Check the App Management and Adding Apps in Dashboard on below document.  https://documentation.meraki.com/SM/Deployment_Guides/Enterprise_Deployment_Guide_and_Best_Practices       ... View more

@JoniM : Whenever you clicked on the mode (routed or Passthrough), you always get the notification to save the changes before proceed further as told by @cmr . When you say double notification, you are saying, the system asked for another question "Are you sure to do the changes" make the system dual click. Meraki is trying to simplify the things with less clicks to deploy. I would suggest you to provide the administrator access to limited person for the dashboard and provide read only access to others.    The reason I am saying this as it is difficult to have multiple opinions to simplify the Dashboard as some required one click and other multiple. Hope you understand the sensitivity here.   ... View more

@JordanTT @Glad to know you get the firmware alerts now  ... View more

Check the traffic shaping rules and the troubleshooting steps  https://documentation.meraki.com/General_Administration/Tools_and_Troubleshooting/VoIP_on_Cisco_Meraki%3A_F.A.Q._and_Troubleshooting_Tips ... View more

@DerekGerard @Hope you got your solution  ... View more

Is it losing or it is not generating the traffic ? Did you test with some other system to check if you can get the traffic from PLCs.  ... View more

This is definitely a support ticket, there is nothing you manually adjust the timer. ... View more

@Bruce @Thank you sir  ... View more

@NetworkDemon : Thank you Sir ! ... View more

@PhilipDAth :Thank you sir  👒 ... View more

@KRobert : Thank you sir. Nothing posted there related to Meraki Yet 🙂     The Blogs are  https://www.thenetworkdna.com/    Cisco Award https://www.cisco.com/c/en/us/training-events/events-webinars/influencer-hub/blog-awards.html#~2020-winners  ... View more

D for @DavidLowe  🙂   ... View more

@UCcert : Thank you sir ! ... View more

Thanks a lot @MeredithW and all the team members of this community  💚 ... View more

@DanielWahlsten @Welcome to the community. You will get to know a lot here, best of luck ! ... View more

@EricaO This is what you are looking for ? https://www.cisco.com/web/dofc/16616456.pdf  ... View more