Hi @dbarr_pxo, thank you for sharing this feedback with us. I'll pass your comment along to our documentation team. They may follow up with you here if they have additional questions for you!   ... View more

this is still a common issue as of Sept 2022,  we are on the most updated firmware. we've had about 40 instances in the last 2 months where we had to call support.    no permanent fix in sight.     ... View more

I've not tested with MR33's but they are Wifi 5 wave 2 AP's so they should support MQTT streaming.   This doc is fairly helpful regarding config and the MQTT schema https://documentation.meraki.com/MR/Other_Topics/MR_MQTT_Data_Streaming ... View more

I, too, need to assign a static IP to an iPad. Everything is configured on the Verizon side but I have no way to change the APN on the iPad. Cellular Network settings are disabled and I can't find anything in Meraki to affect that. ... View more

I believe I've pinpointed the concern. The APN on the MX is modifiable in the portal, but the APN on the MG requires modification at the unit itself. Even if safe mode is enabled, the APN cannot be changed from the portal.    Our activated SIMs require a custom APN. So local configuration will be required. Thank you. ... View more

Muchas Gracias por tus observación. Por el momento tengo un Regla L7 que restringe la mayoría del trafico de video, películas, etc.  Mas mi ideas es buscar un Política de grupo que solo te permita las aplicaciones de Microsoft 365.  Ejemplo, la misma política mostrada pero permitiendo correo y portal web. Agregar cada servicio creo que quedaría un poco larga. Estoy buscando como seria la forma mas correcta. Saludos y gracias por tus comentarios.  ... View more

Hello @C1Meraki  I believe for split tunnel If the option to send all traffic isn't checked to send all traffic through VPN then the traffic just follows the client's routing table and if there are no routes specifying that traffic go through the VPN adapter then nothing will go over the VPN. In send all traffic over VPN checked scenario basically all traffic is sent over VPN interface ... View more

Hello, I'm guess a group policy similar to policy on umbrella dashboard needs to be created. Do you have 2 group policies created for CORP and Guest or are you applying  umbrella policy directly via SSID. ... View more

@BrechtSchamp  but that makes it interesting and means you can't get it wrong 😂 ... View more

Hello @bmehta , @PhilipDAth, @Bruce  Thank you for all your responses and suggestions. Yes, there is no issue with the subnet being added. I was actually wondering if there was a change in the API, as when I used it last month, it took the IP address as is without conversion ( hence the query here ) .  However, I agree with all your suggestions of it not affecting anything if the subnet being added. @bmehta  I will report this issue as it does not take only IP and always converts to subnet. Thanks everyone. Cheers, Craig. ... View more

Thank you, this is good to know. I may need to try them out. ... View more

Hola buenas tardes:   Hay dos formas, en ambas abre las opciones desde la red en donde tienes el problema:   1.- Telefónicamente, en el dashboard en la esquina superior derecha existe un submenu que dice help, oprimes y se despliegan opciones, seleccionas Get Help. Te aparecera el menu de Meraki Support Center abajo de los iconos de lso equipos aparece still need help? das click en la pregunta y te apareceran 4 menus en de la derecha dice Call The Meraki Support Team y te pondra el numero para Marcar a Estados Unidos, se despliegan dos número más uno de Meraki Customer NUmber y Support passcode copia estos número porque los utilizaras o manten la paguina abierta. También te da la opción de maracar de manera Local dependiendo de donde hables (view regional phone numbers). Marcas y te llevara el menu solicitando el número Meraki Customer Number, posteriormente te contestaran y atendera solicitando un númeor a donde te llamen en caso de que se corte y tu nombre.   2.- Levantando un caso en el Dahsboard por correo, en el dashboard en la esquina superior derecha existe un submenu que dice help, oprimes y se despliegan opciones, seleccionas Cases, te aparece abajo una opción en azul que dice newcase, oprimes y te abre una plantilla que solicita información del problema y te contestaran por esa misma vía, te recomiendo seas muy explisito sobre la falla modelo y numero de serie del equipo.   Con estas dos opciones es suficiente. Pueden tardar en contestarte o te pueden contestar en Ingeles colicita soporte en español y te lo consiguen.   Espero sea util la información.   saludos.       ... View more

Oh, and to be clear you can connect cables with switches on, but be aware that a switch with no power supply or power cable will power up as soon as you connect the first stackpower cable. ... View more

No worries, thanks for your reply. ... View more

thanks! ... View more

Hello @SPoulin  Ideally the wifi settings payload profile when pushed and received by device should auto join. If it is happening with one device and not all I would verify if the device is receiving any management instructions from the dashboard.   https://documentation.meraki.com/SM/Profiles_and_Settings/Configuration_Settings_Payloads#WiFi_Settings ... View more

Hi bmehta.   Thanks for your reply, but I don't think it's correct. Well the first part is, but as I wrote it's only L3/L4 so not of any use in my scenario. I need L7 rules.   Regarding bandwidth limit on celluar. Are you sure that the celluar setting is limiting the bandwidth and not indented to make some policy based decision on with connection to use?     Anyway, the ability to make some L7 firewall rules, which could come into play when celluar interface is active, should be the right way to go, and not only L3/L4 rules.   ... View more

yeah, it's fixed now indeed. ... View more

Hello, You can access local status page of the MX via http://mx.meraki.com , http://wired.meraki.com https://documentation.meraki.com/General_Administration/Tools_and_Troubleshooting/Using_the_Cisco_Meraki_Device_Local_Status_Page The IP varies for different MX models but you can look into the above document and get more information on how to do it via IP. It is much easier to leave the client on dhcp and  navigate via your browser and make sure you are directly connected to MX and not connected to any WIFI network on your client ... View more

You can find the links via your dashboard   1-go to help > API docs > organizations > List the uplink status of every Meraki MX and Z series appliances in the organization   2-go to Help > API docs > Devices >Get the uplink loss percentage and latency in milliseconds for a wired network device ... View more

Hello @SCC , As per the document https://documentation.meraki.com/MV/Initial_Configuration/MV_Cloud_Archive it seems that the Copies of video are stored on both the camera and in the cloud. On-camera recording does not change. So the same recording is stored locally and on cloud. It would not add up the days on stage retention. Let me know if any concerns ... View more

Hello, Where do you see this error? on the client or on the dashboard? There are multiple factors that are responsible for Client's connection to AP. The process is as follows https://documentation.meraki.com/General_Administration/Tools_and_Troubleshooting/Analyzing_Wireless_Packet_Captures#802.11_Client_Authentication_Process ... View more