Hello, If an activated SIM is inserted in the MG it should seek a connection and come online. Afaik MG is expected to come online with a a SIM when out of the box. You can add an extra step  by making sure MG comes online and updates it firmware before shipping out to locations so it does not go through the process of upgrading when at the location. Also, you can configure APN and pincode if required on the local page before shipping them out. ... View more

Hello, I would like to know more information on your setup. Are you using Verizon SIM via MX or MG to get a cellular WAN connection? You can apply APN via dashboard in the Appliance status > uplink tab for MX. I'm not sure about APN application your client devices as dashboard cannot apply config to client devices unless it a MDM scenario.  ... View more

Hello Can you provide to know more details on what you would mean by Meraki side of things updated to BGP? On your Meraki organization iBGP information would be exchanged over AutoVPN. When routes are learned from an eBGP neighbor they will distribute to spoke locations via iBGP. If you have not configured eBGP for now then you can  at least make sure the AutoVPN is up between all the locations of your organization. So in the future routes get redistributed correctly. Let me know if it makes sense or you have any concerns. Thank you ... View more

Hola @NachoZuvic , Si está agregando una regla de firewall "denegar todo", deberá permitir IP y rangos específicos. Sin embargo, también puede bloquear la transmisión y otras opciones de Internet a través de las reglas L7. De esa forma, no tendría que bloquear todo el tráfico en esa subred. Además, puede utilizar el filtrado de contenido en esa subred y bloquear sitios web de esa manera. Más importante aún, recomendaría configurar un límite de ancho de banda del cliente en esa VLAN para que los clientes no utilicen el ancho de banda de la red. Espero que esto te ayude. ... View more

Hello @C1Meraki  I believe for split tunnel If the option to send all traffic isn't checked to send all traffic through VPN then the traffic just follows the client's routing table and if there are no routes specifying that traffic go through the VPN adapter then nothing will go over the VPN. In send all traffic over VPN checked scenario basically all traffic is sent over VPN interface ... View more

Hello @thejrace , On the newer models of access points MQTT feature is available.  In order to start configuring MQTT service on MR, please go to Wireless > IoT Settings > MQTT Settings. Select Enable on  Stream Telemetry via Access Points in order to display all Settings to be configured. Let me know if any concerns. There should be a document available soon and I will share it here. ... View more

Hello, I'm guess a group policy similar to policy on umbrella dashboard needs to be created. Do you have 2 group policies created for CORP and Guest or are you applying  umbrella policy directly via SSID. ... View more

Hello, @EricD10 If you have a NAT rule configured for the server you can restrict the IPs / allow only specific IPs in the "Allow inbound connections". Also, having the server in DMZ vlan is always recommended.  https://documentation.meraki.com/MX/Firewall_and_Traffic_Shaping/Creating_a_DMZ_with_the_MX_Security_Appliance ... View more

No dude en abrir un caso con el soporte de Cisco Meraki y compartir toda la información con ellos para que puedan ayudarlo a solucionar el problema. ... View more

Hello, I would recommend following the stacking procedure mentioned here for MS390s https://documentation.meraki.com/MS/Stacking/Switch_Stacks#Stacking_MS390s   https://documentation.meraki.com/MS/MS_Installation_Guides/MS390_Series_Installation_Guide#Stack_Cabling_Installation   Let me know if you have any concerns   thank you     ... View more

Hola, Puede asegurarse de que el AP tenga una conexión de enlace ascendente en funcionamiento a WAN con todos los puertos e IP que permitan el tráfico para la comunicación en la nube de Meraki? Los detalles sobre puertos e IP se mencionan en Ayuda> Información del firewall en el tablero. Puede intentar reiniciar y reiniciar el dispositivo como paso de solución de problemas. ... View more

Hello, The "unable to fetch configuration" error is a known issue within Meraki. You would need to contact Cisco Meraki technical support via email or phone for their assistance in resolving the issue. It is recommended to be on the most recent stable firmware as occurrence of this error is more on the older firmware for MXs. Also, for MXs the recent beta firmware have fixed these issue. Thank you   ... View more

Hello @SPoulin  Ideally the wifi settings payload profile when pushed and received by device should auto join. If it is happening with one device and not all I would verify if the device is receiving any management instructions from the dashboard.   https://documentation.meraki.com/SM/Profiles_and_Settings/Configuration_Settings_Payloads#WiFi_Settings ... View more

Hello, I know that there are some known issues  and limitations with the "current client connection" feature. Please feel free to create a case with Meraki Support so you can track the issue until it gets resolved. ... View more

Hello, Thank you for reaching out. I'll forward the request to our documentation team.   ... View more

Hello @adle, I would recommend you to open a case with Technical Support regarding this issue. It is known issue and the internal team is working to fix it. By opening a case with Meraki Technical support you will be able to track the case for updates or resolution. ... View more

Hello, I believe  this should be possible   https://documentation.meraki.com/MX/Cellular/3G%2F%2F4G_Cellular_Failover_with_USB_Modems#Cellular_Firewall_Rules_and_Bandwidth_Limits You should be able to block non essential traffic from cellular here Under Security & SDWAN > Firewall > cellular firewall rules   You should be able to limit the uplink cellular bandwidth here Under Security & SDWAN > SD-WAN & traffic shaping > Uplink configuration > Cellular limit https://documentation.meraki.com/MX/Firewall_and_Traffic_Shaping/SD-WAN_and_Traffic_Shaping#Uplink_configuration ... View more

Hello, Group policy via API is quickest way I could think of. However, are you using templates in your organization? it should be possible via templates if you use them. ... View more

Hello, You can access local status page of the MX via http://mx.meraki.com , http://wired.meraki.com https://documentation.meraki.com/General_Administration/Tools_and_Troubleshooting/Using_the_Cisco_Meraki_Device_Local_Status_Page The IP varies for different MX models but you can look into the above document and get more information on how to do it via IP. It is much easier to leave the client on dhcp and  navigate via your browser and make sure you are directly connected to MX and not connected to any WIFI network on your client ... View more

You can find the links via your dashboard   1-go to help > API docs > organizations > List the uplink status of every Meraki MX and Z series appliances in the organization   2-go to Help > API docs > Devices >Get the uplink loss percentage and latency in milliseconds for a wired network device ... View more

Hello @SCC , As per the document https://documentation.meraki.com/MV/Initial_Configuration/MV_Cloud_Archive it seems that the Copies of video are stored on both the camera and in the cloud. On-camera recording does not change. So the same recording is stored locally and on cloud. It would not add up the days on stage retention. Let me know if any concerns ... View more