@ITMiltWhitOCSNC 90F/32C ambient in the enclosure is quite high, we set our sensors to alert at 25, 27 and 29 as I think anything over 29C is pretty toastie.  Might well be worth trying an MS130R there. ... View more

We just had this issue on 15.20. There seems to be some kind of relevance to a large L2 domain I think.   This was MS210 ... View more

14.33 is now a stable release so I'd upgrade to that if you haven't already? ... View more

@wwWe've updated everything to the latest firmware and luckily never faced the issue again since then. But however, I've found nothing related to this issue in the any release note... ... View more

This thread makes me never want to upgrade any of my stacks. I'm new to Meraki (old school Cisco here). I would never want to leave some sort of vulnerability open though. My switches are currently on 11.31, and haven't seen any real issues that force me to upgrade. I just see that "Update available" message and think I should.   ... View more

Yeah that is annoying how browsers do that.   Many browsers have an option to disable auto-suggest for a URL.  Find that option and enable it for the Meraki shard you are on. ... View more

Hi,   I'm planning an upgrade to 26.6.1 for quite a few MR42s. It has been a few months since its release and I was wondering if anyone has any recent feedback from their environment running this FW.   I am currently on 25.13 and was thinking we would benefit from the newer more secure code (hopefully). Since the release notes are quite vague, I would like to hear your opinion.    Thank you, Robert  ... View more

It'll be a 100mbit connection.   1st and 2nd pair are data and are tested.  3rd pair is for poe and is tested.  4th pair ... specs says it can be used for poe so not sure.  I don't have a switch with a 100mbit PoE device that isn't affected by the 12.14 bug to test on 🙂 ... View more

Thanks @PhilipDAth. I reviewed the power consumtion and 370W will be enough. ... View more

We've been having an issue where our ISP has had a number of fiber cuts, but when service is restored our meraki devices go into a state where they drop 20-80% of packets until we reboot every switch.   The original issue is obviously the fiber cuts, but would this bug be related to the packet loss after restoration?   Topology wise - main office has two MS350s running MS11.30, and each branch has an MS250 and some number of MS225s?     ... View more

Yes, I also saw that but as the Cisco WiFi phones also drop at the same time (and don't reconnect until AP reboot) I think something bigger is at large.   We will try each new release as it comes due to needing the 26.x improvements but it is a bit of a chore... ... View more

I second what everyone is saying, especially the part about it not being foolproof.  I have a network specifically for BYOD devices so I put in a policy to disallow those devices on another specific network.  It worked 'mostly'; however, it would sometimes block iPads when I only wanted it to block iPhones. (even though they are two unique policies) ... View more

Maybe it´s the old software version. I had trouble with v9.x. With v10.3x I have less trouble.   regards   ... View more

Yes, I have to replace 21 switches in different locations. That is not a good karma.   It would be really nice to get a license duration upgrade or something else.     ... View more

Hey all,   Just chipping in here to say we have created a FAQ page on our Knowledgebase: https://documentation.meraki.com/zGeneral_Administration/Support/MS225%2F%2FMS210-48LP%2F%2FFP_Proactive_Replacement   This is following the advisory we released last month: https://meraki.cisco.com/blog/cisco-meraki-customer-advisories/   As @MerakiDave mentioned above, we have a software mitigation for devices that are not in the failure stage yet, so if you have concerns or you can see issues with the device, get in touch with us at your earliest convenience, so this can be applied for you.   Thank you all for your understanding and patience on this!   Giacomo ... View more

Same thing here. i was told it is a GUI bug and support is on the run to fix all affected networks ... ... View more

It 100% should be PEAP.  Check the log in the Meraki dashboard as well to see if it says anything interesting. ... View more

While it would be useful to be able to read the files I guess Meraki are trying to keep things simple for the customer. Nice that they have added it and well done to @PhilipDAth for suggesting it. ... View more

I have 802.11r enabled at a lot of sites.  Mostly without issues.  It is hard to tell if the end client is actually using it or not though. ... View more

This might solve your problem.. https://documentation.meraki.com/MS/Other_Topics/Staged_Upgrades_for_Meraki_Switches ... View more

Try downgrading to 24-12. I have a customer where this is happening and a downgrade to 24-12 fixed it for the time being.  ... View more

Now that's some good work.  Great job @PhilipDAth ... View more

I had to remove the power cable, after an minute replugging. And the switch was starting and working well. ... View more