Meraki

ManolisFr

I spoke earlier with our provider. He made a reset to the passord of the connection and he set up a new one. The last 5 hours meraki works fine with FTTH connection but the problem is that the max up and down limit you can set on mx64 is 250mbps. Our FTTH is 1000down/500 up So we are planning to change maybe the equipment except if there is a solution to increase the limitations

ManolisFr

Hello NOVA Greece This time i have not connected the ftth to meraki. On saturday and sunday i made a lot of configurations from huawei, trying several different settings. but i never saw the global ip on meraki i added as always pppoe credentials , auto or static global doesn't matter , we have static, and vlan 835 on uplink settings. i also have the same vlan on huawei and it's enabled The wan connection i create on huawei is connected. because of bridge i have no internet to the pc which is connected onlly to huawei (outside of our local network) but i have statistics on the wan i created on huawei. Rx and tx bytes. so i

ManolisFr

We have no problems last 7 years . we have a meraki and till tuesday we had connected on it a technicolor dga-4130 router on bridge mode to internet port and a second asus router to port 4 for load balancing On friday our ISP Send us a nokia ONT and a huawei DN-8245V-70 in which the main FTTH Wan connection is locked and i cannot set it to bridge So i disabled only the wan radio button from the main one and created a second wan connection (on huawei router) the second wan connection Enabled wan yes GE Uplink because of FTTH PPPoe ipv4/ipv6 Bridge wan and vlan 835 (this is the right one from isp) and i made a binding to lan port 2 for the bridge connection On meraki i added wan config enabled, PPPoe , vlan id 835 , our credentials for the isp connection and manual global ip because we have a static one I think that i made something wrong maybe I set vlan id 835 only to the uplink infos Should i open 835 somehow for the internet port? I didn't find any option for the internet port (only for lan ports) we have meraki MX64

ManolisFr · ‎Jun 20 2021

Hello Thanks, i will check it tomorrow but probably you are totally right because during backup procedures from some machines and the server, between 10:00pm and 02:00 we have no alerts..

ManolisFr · ‎Jun 19 2021

Hello Basically we have no problems with disconnectionson our local network. Because of server delays last weeks (maybe sql issue) i enabled the alerts for all the workstations we have about the connections and disconnections from Lan We have a Synology Nas and it working without problems and making automatically backups every day from all the workstations (monday to friday). But every 5-10 minutes i receive a mail that the Nas disconnected ..and after some second connected again. I had enable also mail alerts on Nas but it seems that has no issue. Maybe it's a bug from meraki? I don't know. Does anyone has the same issue?

ManolisFr · ‎Oct 26 2020

hi, It's a TPLINK SG-1024D unmanaged

ManolisFr · ‎Oct 26 2020

Hello . The Synology is connected to our Gigabit Switch. Not directly to the MX64 On the MX are connected only the 2 vdsl connections and a cable to the above switch.

ManolisFr · ‎Oct 25 2020

Thanx a lot Pavan. We have also our server with bonding configuration but we have no events for this "conflict"

ManolisFr · ‎Oct 25 2020

Hello to all We have also in our network a synology NAS in which we have a network bonding How can we disabled the client ip conflict message on event log. I have no alert enabled on alerts tab (in order to send mail for this) But our event log is full of this type of event

Meraki

Community

About ManolisFr

ManolisFr

Community Record

Badges

Re: Trying to bridge a FTTH Connection to meraki but failed

Re: Trying to bridge a FTTH Connection to meraki but failed

Trying to bridge a FTTH Connection to meraki but failed

Re: Client connect and disconnect about 100-200 times a day (Synology Nas)

Client connect and disconnect about 100-200 times a day (Synology Nas)

Re: MX64 Client IP conflict (from Synology NAS)

Re: MX64 Client IP conflict (from Synology NAS)

Re: MX64 Client IP conflict (from Synology NAS)

MX64 Client IP conflict (from Synology NAS)

Re: Client connect and disconnect about 100-200 times a day (Synology Nas)