Considering they just released the MS130 series, they will likely release them under the GS line soon-ish.  ... View more

Hi @macsolutions , one piece of advice - make them know you exist.  If you’re serious about selling and have a customer base to sell into then let your AMs know.  Make use of their experience and resources to help you sell more.  If you’re sitting there waiting for someone to get in touch and make something happen……you’ll be waiting a very long time  ... View more

@MiriamK said they will at some point, but no details as of yet.  ... View more

>Load balancing is enabled. Traffic shaping rules are default.   You can experiment, could you try turning this off please. ... View more

Have you tried just turning off igmp snooping? ... View more

I have the same issue ..port forwarding to vLans.. any resolution? ... View more

I purchased a POE tester to take to the location to test the port as well. Thank you for these ideas. ... View more

Brandon had some really good suggestions, when the fault occurs can you ping 8.8.8.8 from the affected machine to confirm that its just DNS and not full network access?     ... View more

There no "override" for Geo IP blocking, so strictly speaking you can't ... View more

I am having this issue as well, the Air Marshal is not the problem, it is already set to allow,  I Cannot get these lights to connect to an MR56, on an MR52 it is fine, same SSID..... frustrating since the MR52 is far away and does not always connect well.   Any suggestions or recommendations would be appreciated! ... View more

Hey Philip, I have nothing against powerline extenders as a technology by itself because it's basically modulating demodulating like Wi-Fi but over electrical wiring.  However care must be taken with older electrical installations as they tend to have alot of fluctuating noise that causes those connections to be unreliable.  Even having some DC powered device with a low quality adapter even on a different circuit can wreak havoc on powerline homeplugs. My previous job was as a technician troubleshooting home installations for an ISP and my experiences were really bad with those things. Usually a good wireless mesh solution or even a signal modulator over coax can give better results but this all depends on the situation at hand.   For the OP I would strongly suggest getting cables to the other AP's and even do a little site survey to see if the AP signals are OK in both directions. ... View more

I dont have sonos. But i use one vlan for normal home wifi.   And another vlan for iot. In this vlan i only allow iot to talk to iot  and internet.   Asuming you have a mx that uses statefull rules you could  also do something like allow home to iot. And deny iot  to home. ... View more

I would go through the blog again with a fresh set of eyes and see if you notice where you have gone wrong. Failing that I would just call into support, its included in the cost of the license and they should be able to work this one through with you.    Ive spent way too long looking at a setup that should work and finally when I've swallowed my pride and called support they have picked it up in 2 minutes. Sometimes you get abit blind looking at the same setup for so long.  ... View more

This question is a little open.   To use a Z3C you need the physical device and a Meraki licence.  The licence is 1, 3, 5, .. years long.  You might buy the appliance outright, lease it for a monthly cost, or get it from an MSP for a monthly cost.  If you buy or lease it then you will also be buying a licence. The monthly cost of that component is the cost divide by the number of months in the licence.   Now you have the operating costs of whomever you get the Internet from.  You might use a cellular data plan.  You might use fixed-line broadband service. ... View more

Hi @macsolutions  you would see something like the image below at non-Meraki VPN configuration section. That being said. I don't think it is completely ready for client VPN. But if you are looking for non-Meraki VPN, you should be able to negotiate your VPN via IKEv2       ... View more

You could try a packet cpature on the affected device. ... View more

Are you sure you haven't changed the MX from Bridge to NAT mode or turned on DHCP on any of the configured VLANs? Also, the MX has the ability to relay DHCP requests, so while you haven't changed anything on the MX, but yet it a network DHCP server might have come up. I suggest you take a pcap and analyze this in more details. Here is a link for DHCP relay on the MX: https://documentation.meraki.com/MX-Z/DHCP/DHCP_Services#DHCP_relay ... View more