@MerakiDave I'm interested in the URL Logging. I'm looking at the network-wide>general and under reporting, I don't see any tick box for URL logging, I'm running 14.7 on the MX network. Is this still available?  ... View more

Those Gnomes are Baller; I want one 🙂 ... View more

The AP's resort to "Meshing" when an up-link connection cannot be established on the LAN interface of the Access point. My recommendations would be to check the cable to ensure it's not faulty and then also try plugging the cable in to a machine to ensure that the machine can get network connectivity (Correct IP address/Default gateway etc)   Have a read of this document which outlines "Mesh Networking" in more detail - https://documentation.meraki.com/MR/WiFi_Basics_and_Best_Practices/Mesh_Networking ... View more

There's no one button/click to achieve resetting an SSID back to defaults. My recommendation would be to just disable the SSID and then create/enable a new SSID, this would effectively have the "default" settings already pre-populated.  ... View more

Have a read of the MR74 setup guide - https://documentation.meraki.com/MR/Installation_Guides/MR74_Installation_Guide.    The MR74 features band-specific antenna ports, and thus the corresponding band-tuned antennas should be paired with the AP.  ... View more

+1 for renaming this to "CPU utilisation" - Highly misleading otherwise. ... View more

+1 to keeping this Meraki specific.  ... View more

Congrats all 🙂 ... View more

You might also want to check that there is no firewall upstream which could be blocking connectivity to the cloud (help>firewall info) within dashboard shows the range of IP's/Ports that are required to be opened up on the firewall to allow for cloud communication. ... View more

Hey @BlakeRichardson, Managed to get to the bottom of this one. My devices had AV's installed which appeared to have a built in host firewall. Looks like these were blocking some of the outbound ports required 🙂   Cheers. ... View more

From my knowledge there isn't any hard limit of the throughput of the Z3 unless you set one. Therefore the Z3 is able to operate as close as line speed as possible (1Gbs).     ... View more

@BlakeRichardson Thanks Blake, only problem is that there isn't a firewall in the way of these devices.  ... View more

Again as per @PhilipDAth's reply. I don't think this feature is available currently. Make a wish (assume you already have). Reach out to your Meraki Sales rep to get some inside scoop on the MX roadmap for this feature/capability. ... View more

Hello @CarlosCoque, What error message are you getting on your Windows 10 client? I assume it's giving you a Windows 809 error message? Refer to this article which explains how to fix, plus other fixes for other error codes.   https://documentation.meraki.com/MX-Z/Client_VPN/Troubleshooting_Client_VPN ... View more

Surely you could just setup SMTP alerting to go to a email address which is integrated with your NOC ticketing system. The SMTP alerts from Meraki come with a hyperlink embedded to the devices dashboard URL.   ... View more

There currently isn't an up-time clock per-say within the dashboard. If you can't work this out for yourself as per the connectivity monitoring as per the earlier comments, open a support case. Merkai support will be able to provide you information like when the device last rebooted/lost power and the reason behind why. I'd also recommend using the make a wish feature within dashboard to submit a feature request if you believe that this feature should be available via the dashboard. My assumptions is that this is asked for a lot so I can imagine it'll only be time before it's included. ... View more

I agree with @PhilipDAth, the weather in Auckland today is amazing. The Fridge is fully stocked with beers, i'll be pulling one out later in the day! ... View more

Thanks @CarolineS. I also received my gift today! @PhilipDAth Mine came fully stock with beers. The Fedex guy must have taken a hint from your  earlier words!   ... View more

There doesn't yet appear to be a call via the API to statically set a management IP address. (Log into dashboard Help>API Docs).    My recommendation if you're still wanting to statically configure Management IP's would A) Via dasboard/GUI. B) Via creating DHCP reservations on the DHCP server. ... View more

In theory, it will continue to run as per normal when your license expires. (You get a 30 day grace period to be out of license compliance.) You'll need to update/apply a license within this grace period otherwise at the end of the 30 days you'll organisation will be disabled and the appliance will stop "Working". ... View more

Congrats to all the Monthly winners; Especially the new members that have made the list,  It's great to see the community expanding! I'm fizzing to get my hands on some more Meraki SWAG! ... View more