Meraki

RWelch · ‎Oct 16 2024

@RaphaelL I like your suggestions and agree it would make it easier (agree)!

RWelch · ‎Oct 14 2024

It appears in the example above that the cable length grew .75m when the device was powered on. 😆

RWelch · ‎Oct 14 2024

Possibly so - another location to reference is HELP > Firewall Info which shows UDP 123.

RWelch · ‎Oct 14 2024

The Upstream Firewall Rules for Cloud Connectivity references NTP resolution as follows: https://documentation.meraki.com/General_Administration/Other_Topics/Upstream_Firewall_Rules_for_Cloud_Connectivity

RWelch · ‎Oct 14 2024

No, not logging in via SSO. I waited around 5 min and eventually got back into the dashboard. Weird.

RWelch · ‎Oct 14 2024

Anyone else having troubles logging into the Dashboard?

RWelch · ‎Oct 14 2024

Two cables would be needed for a ring configuration setup. https://documentation.meraki.com/MS/Stacking/Switch_Stacks

RWelch · ‎Oct 13 2024

If added manually it should remain until removed. An employee that was terminated was mistakenly removed from the network and later added back manually. We periodically see that same ex-employee pass by (BLOCKED) - and it's remained working that way over the past 3+ years.

RWelch · ‎Oct 7 2024

Have you tried to connect either the Korenix or Meraki via fiber with another device that you know works or is working? Perhaps trying different SFP modules or patch cable (OM2 or OM3) to rule out what isn't working with something that IS working.

RWelch · ‎Oct 7 2024

You should be able to select "All clients with a policy" that would give you the ability to see whitelisted devices.

RWelch · ‎Oct 5 2024

This EARLY ACCESS feature helped me re-look my Non-Merarki VPN Peer settings and "adjust" them to better settings than I used initially in the hustle/bustle to get my networks up/running. Perhaps it will help others re-look their settings. Kudos for this feature.....everyday is a good day to learn!

RWelch · ‎Oct 4 2024

👍welcome!

RWelch · ‎Oct 4 2024

Go to Wireless > Configure > Radio Settings RF Profile tab and EDIT whichever RF Profile you are using

RWelch · ‎Sep 30 2024

You can setup Port Forwarding and NAT Rules on the MX: https://documentation.meraki.com/MX/NAT_and_Port_Forwarding/Port_Forwarding_and_NAT_Rules_on_the_MX

RWelch · ‎Sep 26 2024

@RogerMurdock Yes - I (too) had a similar experience and discovered it boiled down to the way T-Mobile sets up services/devices. The work around that I took was to "ask" for their home cellular gateway appliance and unlimited service. Once I established the T-Life mobile app requiring me to confirm the 6-digit passcode to the home cellular device and service worked on their hardware...I turned off the device and pulled the SIM card. Their home cellular gateway was at NO additional charge. The SIM was put into the MG51 and works as planned - you might have to add your MG IMEI to the plan for the device to work. Probably not the most ideal way to proceed but it got me over the hump per se with establishing T-Mobile service since I wasn't a T-Mobile customer prior to receiving the MG51.

RWelch · ‎Sep 24 2024

Security & SD-Wan > Appliance Status > Summary shows green/red indicator for connectivity or outage. Or Security & SD-Wan > Appliance Status > Uplink will show missing areas if WAN1 or WAN2 are down. In the example above the cellular uplink was repositioned twice and you can see WAN2 outage for brief periods (latency).

RWelch · ‎Sep 24 2024

@GIdenJoe thanks for the feedback. As I mentioned, OM4 remain in place for future hardware upgrades. Always appreciate the dialogue and expert feedback within the Meraki Community.

RWelch · ‎Sep 24 2024

OM4 offers up to 40% higher bandwidth, enhanced stability and reliability. In this upgrade, distance isn't quite a factor as there will be 9 multimode OM4 fiber patch cables replacing the existing OM3 patch cables all under 5 meters in length. All SFP+ or SFP modules remain the same. Just looking to maximize throughput and low latency. OM4 will remain in place for future hardware upgrades. Will it make any or enough difference going from OM3 to OM4? We shall see. OM4 price to upgrade was quite reasonable. Thanks for everyone's feedback.

RWelch · ‎Sep 22 2024

Currently all SPF+ or SPF modules connect OM3 fiber between MX and MS or MS-to-MS devices. Are there any pros/cons if upgrading all OM3 to OM4 fiber (LAN wise or WAN wise)? Dual WAN uplinks are CAT8 wiring to the business grade fiber boxes.

RWelch · ‎Sep 10 2024

https://community.meraki.com/t5/Security-SD-WAN/MX95-running-MX-18-208-Problem-changing-single-WAN1-Uplink-speed/m-p/244142#M54636

RWelch · ‎Sep 10 2024

If it's the same issue, Tech Support sent me these instructions that fixed the issue for my particular setup (7/26/24) and it DID fix the issue: Thank you for contacting Meraki Technical Support! Can you temporarily enable the WAN3 Backup feature, modify the WAN 1 bandwidth settings, and then disable the WAN 3 backup feature, and then try modifying the WAN 1 configuration again just to ensure the WAN 3 backup feature is no longer being referenced? Keep in mind, when temporarily enabling the WAN 3 backup feature, the physical port usage will change to the following: On the MX85, MX95 & MX105 - The Fourth physical port is the designated backup port. Physical ports 1 & 2 become designated WAN 1 and WAN 2 ports.

RWelch · ‎Sep 6 2024

Any idea how/why the MX105 is showing negative data use? I've used Meraki since 2016 and never seen this. MX18.211.3 Thank you.

RWelch · ‎Aug 25 2024

Thank you @GIdenJoe. I wasn’t changing the MTU size rather setting STP root priority bridge when I noticed the dashboard notification on the page when doing so.

RWelch · ‎Aug 24 2024

The dashboard indicates MS425 is limited by hardware to Max MTU size of 9394. The MS425 Overview and Specifications page shows Max MTU size of 9416. https://documentation.meraki.com/MS/MS_Overview_and_Specifications/MS425_Overview_and_Specifications I have two MS425s at separate locations. Anyone else encounter this? Thank you.

RWelch · ‎Aug 4 2024

@KarstenI @cmr @PhilipDAth - thank you for your feedback. I have never enabled any Storm Control features or settings from the Switch Settings page but when selecting "Try New Version" at the top RH corner, there is now info listed under Storm control section of the UI. When I revert back to the "View Old Version" it lists nothing. I have not enabled it so it isn't impacting anything but the new page makes one think it's been configured. I am not so fond of the new UI page so I plan to stick with the View Old Version. .

About RWelch

RWelch

Community Record

Badges