Meraki

AjitKumar · ‎Jun 22 2019

Hi I could think of two ideas. 1. Let us have all the VLANs on MX. OR 2. If you place L3 Below MX. Do enable Track by IP address under Addressing and VLAN.

AjitKumar · ‎Jun 21 2019

Hi Well these are some common features of Cisco Meraki Solutions. Zero Touch Provisioning Dashboard - Single Pane of Glass Centralized Management Various other features of solution....

AjitKumar · ‎Jun 20 2019

Thank you for the information mate. I appreciate it. Perhaps I was under the same understanding until I realized one of my MX client did not renew the license for 8 months. After 8 months I could get the renewal deal. However till then his network worked. This was a surprise to me as I told customer to renew else his network will stop working. However I completely agree with your comments.

AjitKumar · ‎Jun 20 2019

Hi I understand your device continue to work with the existing configuration. You will not receive updates. Your dashboard will not allow you to manage and configure the devices any more. You loose access to all the analytics and reports. If you do not like any of the options suggested by community members. I shall recommend continue using it. Who knows if any day there is real need you may simply buy license and activate the dashboard and continue using the solution with all the features.

AjitKumar · ‎Jun 20 2019

Hi With my Zero Knowledge with APIs. I hope you are using the following Url Format. https://api.meraki.com/api/v0/networks/ Note I may be completely Wrong.

AjitKumar · ‎Jun 20 2019

Hi Andreas Does the following communication helps you? https://community.meraki.com/t5/Solutions-APIs/New-MV-API-Returns-video-link-for-the-specified-camera/td-p/27916

AjitKumar · ‎Jun 20 2019

Hi This is strange. How about firmware update? VLANs are on MX? Also hope the firewall is in Routed Mode not Passthrough Mode.

AjitKumar · ‎Jun 19 2019

Hi I understand disabling Proxy ARP may not be possible. Lowering the bit rate under SSID configuration seems to be a method to control this. I found an interesting article explaining this. Kindly have a look if already not. https://meraki.cisco.com/blog/2018/02/floods-and-broadcasts/

AjitKumar · ‎Jun 19 2019

Hi I understand this should work smoothly. As long as M2 has proper internet I do not see a challenge.

AjitKumar · ‎Jun 19 2019

Hi Erik I understand by default Meraki Wireless network will not block any content unless we configure Firewall and Access Control on the dashboard. Or you have a upstream firewall to filter contents. When you say wired works fine does that mean you are connected to Meraki Switch. How are you bringing internet to switch? How do you provide power to 9 APs? Could you please share some more information on your connectivity?

AjitKumar · ‎Jun 19 2019

Hi If your customer is not in need of a full fledged firewall Z3C shall be fine.

AjitKumar · ‎Jun 17 2019

Hi, With my limited hands on with MS. What is the LED Status of Stack Port? [I guess there is LED for stack ports too ? Not Sure though] How about updating the Firmware? Login to Local Status Page? [I am not sure if there is an option to toggle stack ports status]

AjitKumar · ‎Jun 17 2019

Hi David MR on its own may not be able to do so. However it can segregate traffic as @vassallon suggested by tagging the SSID to appropriate VLAN. Once the traffic is segregated your gateway appliance shall route the subnets to desired WAN interfaces. If you are using MX as your gateway appliance Security & SDWAN->SD-WAN & traffic shaping may help you to do so.

AjitKumar · ‎Jun 17 2019

Hi Joe I may be completely Wrong. How about other services except SSH. Do they work fine? For a customer of mine the slowness was improved by tweaking the MTU values. How about using Netalyzr to verify this? You may check the following Url for MTU troubleshooting. https://documentation.meraki.com/zGeneral_Administration/Tools_and_Troubleshooting/Troubleshooting_MTU_Issues

AjitKumar · ‎Jun 17 2019

Hi, 194.70.89.182 is this IP on which Port Forwarding is enabled?

AjitKumar · ‎Jun 16 2019

Hi, I understand Dashboard on its own may not be able to give you such report. A "syslog" integration may help you to capture most of the information. However, Network-wide->Clients Organization->Summary Report certainly offer you with some details.

AjitKumar · ‎Jun 15 2019

Hi Jeff Hope you have installed certificate for TLS on your AD server. Kindly refer to the following Url. https://documentation.meraki.com/MX/Client_VPN/Troubleshooting_Client_VPN#Windows_Error_691

AjitKumar · ‎Jun 14 2019

Hi I believe APIs can help you to extract the desired information from the Dashboard. Thereafter you may use this information to creat your report.

AjitKumar · ‎Jun 14 2019

Hi Please check the following Url. Hope this document answers your question. https://documentation.meraki.com/MS/MS_Overview_and_Specifications/MS355_Overview_and_Specifications

AjitKumar · ‎Jun 14 2019

Hi, Meraki switches use LACP to provide Layer 2 link aggregation. You may refer to the following Url. https://documentation.meraki.com/zGeneral_Administration/Tools_and_Troubleshooting/Link_Aggregation_and_Load_Balancing

AjitKumar · ‎Jun 13 2019

Hi, Certainly. MX uses the VRRP, for sharing uplink health and connectivity status information between appliances. VRRP heartbeats are sent across the LAN interfaces on each VLAN every second. If no VRRP keepalives are heard by the secondary MX on any VLAN after three seconds, the dead timer will expire triggering a failover event. The concept is explained neatly at the following Urls. https://documentation.meraki.com/MX/Networks_and_Routing/NAT_HA_Failover_Behavior

AjitKumar · ‎Jun 13 2019

Hi, I believe the LocaL Status Page shall display the "Online" status.

AjitKumar · ‎Jun 10 2019

Hi Hope you have gone through the following Url. https://documentation.meraki.com/MS/Layer_3_Switching/Layer_3_Switch_Example Meraki Switches do not have CLI.

AjitKumar · ‎Jun 7 2019

Hi Ben This is very much possible with Meraki. However you may also consider the approach suggested by @kYutobi.

AjitKumar · ‎Jun 7 2019

Hi I understand your approach of moving devices between networks are the only options to bring the configuration to defaults. I do not see any option of resetting the configuration to default for selected device on the dashboard. One Idea could be to refer the change log and revert the settings. However this may not be accurate and is a BIG pain.

About AjitKumar

AjitKumar

Ajit

Community Record

Badges