Meraki

redsector · ‎Aug 28 2018

I know that the software updates didn´t helped. So this is why I had to replace all these switches in the last month. The question now is: was this replacement resolving the issue or do I have to replace all the switches again. Until now I did´t have any temperature issues.

redsector · ‎Aug 28 2018

Oh no, I got a mail from Meraki that I have to replace 21 Meraki MS225-48LP switches. But I am wondering why. I had to replace switch by switch the last 18 month because of the fan issue. And now I have to do it again? Im worrying how to do that.

redsector · ‎Aug 6 2018

Yes, I had to change some switches three times to get a good one.

redsector · ‎Jul 24 2018

No, each switch will keep the own IP-address.

redsector · ‎Jul 24 2018

Wanted to do the updates last week from 10.6 to 10.29 while the 10.30 was arriving. So I changed my schedules to 10.30 beta. And while upgrading to 10.30 the status changed from beta to stable release candidate. This quick changes where pleasantly surprising me. But now in the end everything is working well with 10.30

redsector · ‎Jul 15 2018

Yes, while upgrading from 9.x to 10.x we had some spanning-tree loops too. It was with stacks. But after this all the upgrades were working fine. 10.x has some nice features and spanning-tree configs that I can use. And it´s more stable in the end. So, now I did update 7 of our 8 networks. The last one I will do in two weeks when the other networks are doing well.

redsector · ‎Jul 12 2018

Hi, I want to update my switches (many MS-8P and MS220 and MS225, some are stacked) from 10.6. to 10.29. I want to remove some stacking issues and I like to have the UDLD and the spanning-tree guard feature. Are there any experiences with that update? Thank you Markus

redsector · ‎Jul 4 2018

After weeks spending with support and a Cisco Case Cisco made a patch on our Cisco-ISE. It´s working better now, not perfect but better. Now we have this ISE versions: Version: 2.2.0.470 Patch Information: 1,2,7,8,9

redsector · ‎Jun 14 2018

Hello, We have an problem with our guest WiFi. The splashpage from the ISE doesn´t appear for signing in. With Windows notebooks, Android devices and Apple Notebooks it´s working well but not with Apple iPhones (from IOS 11.3 and 11.4). Its working with the iPhones on Cisco Controller based wireless LAN conncted to the same ISE. Has anybody problems with iPhones and Meraki and Cisco ISE?

redsector · ‎May 4 2018

I have got eight wireless networks with MR32, MR33, MR42, MR52 (not MR34) on firmware version 25.11 and they are working well.

redsector · ‎Apr 25 2018

You can do redundant links with port aggregation. Then you don´t need STP.

redsector · ‎Mar 13 2018

I agree to that.

redsector · ‎Feb 6 2018

Its marked with an arrow when in forwarding status.

redsector · ‎Jan 23 2018

I like 10.9 10.x has Loop-Guard for the uplinks. Switch stacking issues are gone now with 10.x It´s running well on a network with 23 switches MS220 and MS225, stacked and non-stacked, layer2 and spanning-tree, aggregated ports and connected to Cisco 3850 distribution switches and Cisco Catalyst 6800 Cores.

redsector · ‎Jan 19 2018

Maybe the cable had an loose connection. If you pull it back to the first port and checking if it´s good connected you will find out if this was the problem. Turning off the power saving for the network card will not save a lot of energy, I think you won´t find a difference in the energy bill. regards

redsector · ‎Jan 18 2018

- I had this kind of problems with Dell PC´s. After firmware updateing the network card it was gone. - Some other devices like Apple iMacs had this problem, and I solved it with fixing speed to 1GBit on the switch, since then there wasn´t this problem appearing - some other devices had a power-saving problem, and then the link speed changed all the time. After switching off power saving the problem was gone. good luck.

redsector · ‎Jan 11 2018

I have got Cisco SFP-10G-SR-C SFP´s working well in Meraki MS225-48LP.

redsector · ‎Dec 22 2017

Yes exactly. The port is shut down complete. No traffic no power.

redsector · ‎Dec 14 2017

I think they like to bridge because they don't have the same Network (VLAN). Can you look if the VLANs are routed that the accesspoints can see each other in the cabled LAN? Otherwise they see an "unconnected" (to the same (V)LAN) accesspoint and want to mesh it.

redsector · ‎Dec 6 2017

Cisco switches are shown as a rhomb in the topology view. When you point at the rhomb symbol you will see the switch name, port and so on. You need to switch on lldp and or cdp protocol on the Cisco switches. Cloud integration is not supported.

redsector · ‎Dec 5 2017

Here the splash page comes up when you choose an web page you didn´t used before. We think previous used web pages are in the browser cache and lead to not upcoming splash page.

redsector · ‎Dec 5 2017

yes, so it is.

redsector · ‎Dec 5 2017

Hi, we use Cisco ISE as an radius server. The ISE is connected to the Microsoft AD and the Meraki WLAN is connected to the ISE. Once a user wants to connect to the internal SSID the ISE checks if the device is allowed to go to the internal LAN (it´s checked if windows devices have an certificate and if the useres connecting with their AD account to the SSID). If the device is not allowed to the internal LAN it will placed to the "external" (V-)LAN for internet connect. Guests will connect to an Guest-SSID with frequent changing preshared keys routet dirctly to an external VLAN for internet access. regards redsector

redsector · ‎Oct 27 2017

Meraki said to me that after the updates the problem would be solved, but it wasn't. I had to take a video (with sound) of the problem, uploading in the "Cases". After this Meraki made an RMA.

redsector · ‎Oct 10 2017

I made cases for my switches which are doing high/low fan speed. Merkai sent me new switches and now the fan speed is good. regards

About redsector

redsector

Markus Moses

Community Record

Badges