Meraki

ww · ‎Oct 24 2024

If it has a factory config it broadcasts a ssid you can connect to and set a static ip https://documentation.meraki.com/MR/MR_Installation_Guides/MR46_Installation_Guide#Basic_Troubleshooting

ww · ‎Oct 23 2024

Im not sure if this is what you referring to. But you can set at organization>early access > new landing page

ww · ‎Oct 22 2024

If you have a internet firewall on hq you could use one armed mode. If you want to use the mx as hq internet firewall you run routed mode. MX ospf doesnt learn routes. If possible use bgp for dynamic routing

ww · ‎Oct 19 2024

try reboot the switch. If it still doesn't work after reboot contact support.

ww · ‎Oct 19 2024

If you just have one mx i would use this. https://documentation.meraki.com/MG/General_Configuration/MG_IP_Passthrough This way you dont have double nat and it would be easier to active a service like client vpn. If you just provide basic internet or have a warm spare setup nat mode on mg would works fine to.

ww · ‎Oct 17 2024

With adv sec license you can use content filter categories. You can also block urls manually. There are also pre defined add block lists on internet that you can put in manually Meraki doc: https://documentation.meraki.com/MX/Content_Filtering_and_Threat_Protection/Content_Filtering

ww · ‎Oct 14 2024

You can create a static 0.0.0.0 to your firewall at the hub. And enable that route to advertise in your autovpn. But all your local hub traffic also follows that route

ww · ‎Oct 14 2024

So you could not use a general vpn default route . And then use source based default route for the vlans that want to use mx250 as default route

ww · ‎Oct 13 2024

Regarding the stp. Are you running mstp on the 3850? https://documentation.meraki.com/MS/Port_and_VLAN_Configuration/Configuring_Spanning_Tree_on_Meraki_Switches_(MS)#PVST.2FPVST.2B

ww · ‎Oct 11 2024

This should be assigned/offered by the isp. So i think you have to ask them

ww · ‎Oct 10 2024

After 8 hour https://documentation.meraki.com/General_Administration/Cross-Platform_Content/Behavior_during_Connection_Loss_to_Cisco_Meraki_Cloud#MX_security_appliance

ww · ‎Oct 7 2024

Latency would show a gap if you dont have service for 4-5 minutes. You have a default route in vpn? Are there no event logs

ww · ‎Oct 7 2024

Wireless users are in the same vlan as wired users?

ww · ‎Oct 7 2024

No, you could work something out using a scheduled api call. But it would be better to fix the issue, maybe firmware related? What firmware version are you running?

ww · ‎Oct 5 2024

Yes. If you want to use the native switch port vlan (1).

ww · ‎Oct 4 2024

Are you assigning a ip in the native switch port vlan? If so, leave the MR vlan field empty

ww · ‎Oct 4 2024

Like @Mloraditch says. Dont set to vlan1. Use vlan tagging: disabled else you get tagged vlan 1 traffic instead of native vlan traffic.

ww · ‎Oct 4 2024

MS switches can dynamically assign a VLAN to a client device by configuring the switch port to use the VLAN ID received via the RADIUS attribute Tunnel-Pvt-Group-ID https://learn.microsoft.com/en-us/previous-versions/windows/it-pro/windows-server-2008-R2-and-2008/cc772124(v=ws.10)?redirectedfrom=MSDN https://documentation.meraki.com/MS/Access_Control/MS_Switch_Access_Policies_(802.1X)#Dynamic_VLAN_Assignment

ww · ‎Oct 3 2024

Try latest stable.firmware And reboot the switch If it still not working then contact support

ww · ‎Oct 3 2024

Which model switch?

ww · ‎Oct 3 2024

What sfp are you using? Did you set pppoe on the local status page?

ww · ‎Oct 2 2024

I think wifi works. But it Looks like a dhcp server or client issue now.

ww · ‎Oct 2 2024

Network wide > event log > for access points And Wireless > health > select ssid for printer Ssid settings:

ww · ‎Oct 2 2024

Did you check the logging for errors? Could you try without 802.11 w/r Could you try without band steering

ww · ‎Oct 2 2024

After you apply a fw rule, you need to make sure the flow (stop the ping) is not active for 10 minutes. On the live tools you can see start live fw logging to see what rule(s) it hit. So start log > then start ping

About ww

ww

Community Record

Badges