Meraki

ww

It still doesnt work. Can we still get a 5y lic? And how?

ww

There is. You just assign any vlan to the port(s). You dont need to create or name vlans like catalyst

ww

Organization >early accces. The enable vlan profiles

ww

This doc should cover nat exceptions https://documentation.meraki.com/MX/Networks_and_Routing/NAT_Exceptions-No_NAT_on_MX_Security_Appliances#Publicly_routable_LAN_subnets_and_DMZs

ww

Saml users dont have api keys. So that would not be an option

ww

Make a transit vlan/ subnet between the two devices. Then create all static routes with tracking with next hop the other mx ip https://documentation.meraki.com/MX/Networks_and_Routing/MX_Routing_Behavior#Static_Route_Tracking This describes it better but instead of mpls you use the fiber https://documentation.meraki.com/MX/Deployment_Guides/MPLS_Failover_to_Meraki_Auto_VPN

ww

You would need to use bridge mode on the ssid. Or a syslog server that collects all mr flows to find it.

ww

Did you test that from your lan side? Or from another public ip or public port scan tool? From the outside everything should be denied. Unless you maybe enabled no nat

ww

And all switch-switch connections have native vlan 1? Switch 3 and 4 are also meraki? Who is the root switch in your network?

ww

https://community.meraki.com/t5/Security-SD-WAN/Port-Forwarding-and-Firewall-Rules/m-p/133567#M33440

ww

All mx and switch trunk ports use the same native vlan? All switch-switch ports have stp enabled? ----- is not a real physical link ?

ww

Get https://developer.cisco.com/meraki/api-v1/update-network-appliance-traffic-shaping-vpn-exclusions/

ww

That could work. You must connect mg to wan1. Build-in cellular will be used as wan2. https://documentation.meraki.com/Architectures_and_Best_Practices/Cisco_Meraki_Best_Practice_Design/Best_Practice_Design_-_MX_Security_and_SD-WAN/Meraki_SD-WAN#SD-WAN_over_Cellular_Active_Uplink

ww

In case you have client balancing enabled in the wifi profile. Try turning it off

ww

The device didn't receive vrrp packets from the the master. So it moved to active. Then it starts receiving vrrp packets again and moves to backup. Master Down Timer: Time the backup router waits for the IP address owner router advertisements before assuming the role of IP address owner router. Looks like the layer2 connection between the devices is not stable

ww

It is a event of the port going down and up. I assume this is not good when there is a AP connected to that port. This should only happen at firmware upgrades or port/power schedules. Check if the cable is good. and the switch has enough poe power (in case you have many PoE devices)

ww

Stp topology only uses the native vlan. So keep your native vlan consistent in your network. Meraki Management vlan is just any ip that talks to the cloud. Not related to stp

ww

https://documentation.meraki.com/MX/Other_Topics/IPv6_Support_on_MX_Security_SDWAN_Platforms_Core_Fundamentals#Terminologies https://en.m.wikipedia.org/wiki/Provider-independent_address_space

ww

Didn't you set a password in the dashboard? https://documentation.meraki.com/General_Administration/Tools_and_Troubleshooting/Using_the_Cisco_Meraki_Device_Local_Status_Page#Changing_Log-In_Credentials

ww · ‎Dec 4 2024

In the sec center you can go to filter and select clean and unknown. If there file is there you can copy the sha256 string and whitelist them in the allow list at the amp settings

ww · ‎Dec 3 2024

https://dhcp.msu.edu/help/randommac.html

ww · ‎Nov 25 2024

For 18.2 Firmware 18.2 and above: Class Based Weighted Fair Queueing with Deficit Round Robin is enforced on token bucket allocations. Allocation ratios are as follows: Realtime: 8 High: 4 Medium: 2 Low: 1

ww · ‎Nov 19 2024

For internet traffic you can packet capture the internet port when doing a dns lookup. Then look if you see the spesific dns lookup in the capture. For vpn traffic you can see it at the vpn status page. Uplink decisions

ww · ‎Nov 18 2024

You can't do that on mx

ww · ‎Nov 18 2024

That sounds like a bug from 18.211.2 firmware You could try the .4 upgrade

About ww

ww

Community Record

Badges