Meraki

DarrenOC · ‎Dec 2 2020

Well done all. Special congrats to @DarkRobo and @viksep @jdsilva - maybe next time 😉

DarrenOC · ‎Nov 27 2020

HI @DR1 For MSP access you need to reach out to Meraki support not the community support here. For BETA access contact your Meraki or Cisco Partner AM.

DarrenOC · ‎Nov 19 2020

HELP! Where’s my badge for FIT1? Think I completed it

DarrenOC · ‎Nov 19 2020

Interesting one. Thanks for sharing. Will take a look through some of our Orgs

DarrenOC · ‎Nov 18 2020

Same result in different browsers? Clear cache try again?

DarrenOC · ‎Nov 18 2020

Hi @Noffal, correct. You will be fine using either.

DarrenOC · ‎Nov 17 2020

Just reread the question.....so you have devices in different Time Zones so I'm assuming these are geographically dispersed. You can only set a single Time Zone for each network so the answer to your query would be no.

DarrenOC · ‎Nov 15 2020

@cmr , I’ll raise your ATM-25 network with an x.25 military packet switched network built back in 1976. 😁

DarrenOC · ‎Nov 13 2020

Well deserved @Bruce. CUCM 3.2! Same entry point as myself into the world of IPT. Remember dblhelper.exe?

DarrenOC · ‎Nov 12 2020

Hi @REsteban , No offence meant. I attended a pre-launch webinar and the figure touted was 7. Hence where I got the number from. Regards

DarrenOC · ‎Nov 12 2020

From this document: https://documentation.meraki.com/MX/Cellular/3G%2F%2F4G_Cellular_Failover_with_USB_Modems Setting Up a Cellular Modem as an Uplink Please note that upon first-time bootup and connection to the Meraki Cloud, an ethernet WAN connection must be used to download the initial configuration and get the device online the first time.

DarrenOC · ‎Nov 12 2020

Hi @Vhuphilo , you need to register the device to the internet via its WAN interface before failing over to LTE.

DarrenOC · ‎Nov 12 2020

Hi @REsteban, my understanding is that it’s 7 sensors per MV or MR

DarrenOC · ‎Nov 9 2020

love a bit of QoS. mls qos trust dscp, or - the best bit of code written - auto qos trust....

DarrenOC · ‎Nov 9 2020

hi @IMustafaSaleh , as @Bruce eludes to below, reach out to your Meraki AM or support. I believe there's a calculator to work these things out.

DarrenOC · ‎Nov 9 2020

B

DarrenOC · ‎Nov 6 2020

Same here

DarrenOC · ‎Nov 6 2020

Literally just received one. I guess we don’t need to go hunt the client down as I assume this is a false positive

DarrenOC · ‎Nov 4 2020

Hi @jay_b , just to reiterate what @KarstenI states we have this setup across a number of sites. MXs being used as perimeter firewall and ASAs being used for client and third party VPNs

DarrenOC · ‎Nov 4 2020

Hi @nikmagashi , take a read through the below document: https://docs.microsoft.com/en-us/microsoftteams/qos-in-teams Looking at that document and your rules Teams Video Conferencing will hit rule 4

DarrenOC · ‎Nov 3 2020

Hi @TaniaSanchez , attached a webinar on this back in October. The sizes are to do with throughput. vMX-S (200Mbps) xMX-L (1Gbps) Dont believe these are available as yet though.

DarrenOC · ‎Nov 3 2020

@KarstenI - The weekend was information overload and quite intense (was my first time dipping my toe into coding). Was a good laugh for me and my colleague though.

DarrenOC · ‎Nov 3 2020

Great effort all. Especially well done to @Bruce , enjoyed reading your posts and also to @Hal9K and @GFrazier

DarrenOC · ‎Nov 2 2020

Well done all. And special thanks to @MeredithW for organising the event. It went very smoothly especially all the back office stuff that the participants didnt see. @KarstenI - I did spot the T-Shirt. Was this from the Barcelona event earlier in the year? Was a good weekend.

DarrenOC · ‎Nov 1 2020

Hi @MerakiMed , reach out to your Meraki AM to discuss the Beta programme. And yes, it would mean running Beta firmware for a period 😕

About DarrenOC

DarrenOC

Darren O'Connor

Community Record

Badges