Well done all especially @Lourdes  and @jbright    ... View more

Missing here also. Did a double take earlier today when reviewing a specific Org.  Switches ✅ MX ✅ APs …. 🤷‍♂️ ... View more

Design sounds good in theory but as @Tore has highlighted STP may be an issue with dual links. ... View more

So you had an IP conflict? But then surely the ERP traffic would have failed as well?   Glad to hear the issue is resolved.   See you in 2022 ... View more

Hi @Ubaidkhan , what did you do to resolve? ... View more

Any chance you could provide a rough network diagram incl the subnets in question? ... View more

Hi @Ubaidkhan , is there an upstream firewall in Dubai? This is probably not aware of your IP subnets in Pakistan and is also probably blocking the internet traffic from that site.  Do you have access to that firewall to investigate? ... View more

Not in my experience.  Seems like a pointless request. What if you’re the admin and you’re on the side of the world to where the APs located? How could you be expected to take a picture or video then?   Argue your case and push back. ... View more

Hi @Kevin_C  - You mention just windows devices, will this extend to Chrome and Apple devices especially within the ed sector space. ... View more

if you have the time why not strip the stacks down again and put only the MS225's together and likewise with the MS210's (so only stack like with like) and see if the LED status remain the same.  Maybe its a quirk with stacking the two together....but as I've said before, i've never noticed the difference in status lights. ... View more

To be honest I've stacked hundreds of these and never noticed the difference in the LED status on either the MS210 or ms225.  If I can see the stack in the dashboard then I'm happy 😁   Are any of the switches complaining about connectivity to the dashboard?  If not...then nothing to worry about. ... View more

hi @ganeshjadhav  - could you expand on the details of your network setup please?     - Apart from the MX what else does your network comprise of - what's downstream of this device - switches, AP's?  - How are you clients connecting - wireless, wired?  - where are your L3 Vlan interfaces configured - switch/MX?  - What DNS are you using and where does that service reside?  - if you have two WAN/ISP's are you load balancing between the two?  - have you tried isolating one of the WAN connections to see if its a particular one giving you issues?  - what troubleshooting steps have you taken thus far.....? ... View more

thats a tad alarming:   MS390 ports are not disabled when configured to do so in dashboard   Whats an admin supposed to go, go down to the cabinet and put sellotape over the port? ... View more

Hi @RoadstoneUK - yep its there in the 14.32 release notes:   Known issues MS390s may experience control plane resets which could impact dashboard connectivity. This does not affect data plane traffic.   i concur with @KarstenI, The MS390's will unfortunately not be on our radar for future customer deployments until the list of bugs is drastically reduced.   Hope your weekend goes smoothly. ... View more

well done all, especially @js7 and @BazMonkey - great beard BTW. ... View more

also this one:   MS390 management plane may experience brief outages which will show as red lines on the connectivity bar in dashboard. These events do not affect control or data plane traffic. ... View more

Also this one:   In rare circumstances, MS390 series switches may disconnect from dashboard until rebooted. Data plane traffic is not impacted unless RADIUS authentication is used (present since MS 14.28) ... View more

Hi @RoadstoneUK , what firmware version are you running?   There's a known issue with MS 15.6:   Known issues MS390 management plane may restart which will show as an outage on the connectivity bar in dashboard. This does not impact data plane traffic but can cause disruptions to RADIUS authentication (present since MS 14) ... View more

Concur with @BrandonS. Keep it simple and configure DHCP on your MX ... View more

cheers @ww - I did find that document but looks like I missed the piece about only being supported on MR and MX devices. ... View more

Hi @Henk1961 , @cmr is correct you can only clone and replace like for like switches.  It’s only a single switch so doing this manually will be simple and straightforward  ... View more